Whirlpool WRF767SDEM Use & Care Guide - Page 38

PERFORMANCE DATA SHEET Water Filtration System Model P9WB2L/P9RFWB2L Capacity 200 Gallons (757 Liters) System tested and certified by NSF International against NSF/ANSI Standard 42, Standard 53, and Standard 401 for the reduction of substances as listed below. This system has been tested according to NSF/ANSI Standards 42, 53 and 401 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, and 401. Substance Reduction Aesthetic Effects Maximum Permissable Product Water Concentration Influent Challenge Concentration Average% Reduction Chlorine Taste/Odor Particulate Class I* 50% reduction 85% reduction 2.0 mg/L ± 10% At least 10,000 particles/mL 97.0% >99.9% Contaminant Reduction Maximum Permissable Product Water Concentration Influent Challenge Concentration Average%Reduction Lead: @ pH 6.5 / @ pH 8.5 0.010 mg/L 0.15 mg/L± 10% >99.3% / 98.6% Benzene p-Dichlorobenzene 0.005 mg/L 0.075 mg/L 0.015 mg/L ± 10% 0.225 mg/L ± 10% 93.8% 99.8% Carbofuran Toxaphene 0.040 mg/L 0.003 mg/L 0.08 mg/L ± 10% 0.015 ± 10% 81.9% >95% Atrazine Asbestos Live Cysts† Turbidity 0.003 mg/L 99% 99.95% 0.5 NTU 0.009 mg/L ± 10% 107 to 108 fibers/L†† 50,000/L min. 11 NTU ± 10% 87.0% >99% >99.99% 96.9% Lindane Tetrachloroethylene 0.0002 mg/L 0.005 mg/L 0.002 ± 10% 0.015 mg/L ± 10% >99.2% >96.6% O-Dichlorobenzene Ethylbenzene 0.60 mg/L 0.70 mg/L 1.8 mg/L ± 10% 2.1 mg/L ± 10% 92.3% 86.9% 1,2,4-Trichlorobenzene 2,4 - D 0.07 mg/L 0.07 mg/L 0.210 mg/L ± 10% 0.210 mg/L ± 10% >99.8% 88.5% Styrene Toluene 0.1 mg/L 1.0 mg/L 2.0 mg/L ± 10% 3.0 mg/L ± 10% 99.6% 93.5% Endrin Atenolol 0.002 mg/L 30 ng/L 0.006 mg/L ± 10% 200 ± 20% 81.7% 95.7% Trimethoprim Linuron 20 ng/L 20 ng/L 140 ± 20% 140 ± 20% 96.1% 96.3% Estrone Nonylphenol 20 ng/L 200 ng/L 140 ± 20% 1400 ± 20% 95.3% 95.5% Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.75 gpm (2.84 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters). The compounds certified under NSF 401 have been deemed as "emerging compounds/incidental contaminants." Emerging compounds/incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality. ■ It is important that operational, maintenance, and filter replacement ■ The water system must be installed in compliance with state and requirements be carried out for the product to perform as advertised. local laws and regulations. Property damage can occur if all instructions are not followed. ■ Do not use with water that is microbiologically unsafe or of unknown ■ Use replacement filter P9RFWB2L, part #EDR2RXD1/EDR2RXD1B. quality without adequate disinfection before or after the system. 2014 suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices Systems certified for cyst reduction may be used on disinfected are subject to change without notice. waters that may contain filterable cysts. ■ The filter monitor system measures the amount of water that passes EPA Est. No. 082047-TWN-001 through the filter and alerts you to replace the filter. ■ Refer to the "Warranty" section for the Manufacturer's name and Style 1 - When Order Filter is illuminated yellow order a new filter. telephone number. When Replace Filter is illuminated red, it is recommended that you ■ Refer to the "Warranty" section for the Manufacturer's limited replace the filter. warranty. Style 2 - Press OPTIONS or SETTINGS and select Filter Status to check the status of your water filter. When the filter status shows Application Guidelines/Water Supply Parameters 10% remaining, order a new filter. When the filter status shows 0% remaining, it is recommended that you replace the filter. Style 3 - Press FILTER STATUS to check the status of your water filter. When the filter status shows 10% remaining, order a new filter. When the filter status shows 0% remaining, it is recommended that Water Supply Water Pressure Water Temperature Service Flow Rate City or Well 30 - 120 psi (207 - 827 kPa) 33° - 100°F (0.6° - 37.8°C) 0.75 gpm (2.84 L/min.) @ 60 psi you replace the filter. ■ After changing the water filter, flush the water system. See "Water and Ice Dispensers." ■ These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary. ■ The product is for cold water use only. *Class I particle size: >0.5 to