Whirlpool WRF954CIHV Owners Manual - Page 17

Refrigerator Leveling, and Door Closing

Page 17 highlights

8. Repeat steps 2 through 7 to install the other handle onto the adjacent refrigerator door. Freezer Drawer 1. With the drawer closed, place the handle onto the shoulder screws so that the setscrews are facing down toward the floor. A B A. Shoulder screw B. Setscrews inside the handle 2. Firmly push the handle toward the drawer until the handle base is flush against the drawer. 3. Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until key is engaged in the setscrew. Remove the Handles 1. While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew. 2. Using a right-to-left motion, loosen the setscrew a quarter turn at a time. 3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer. 4. If necessary, use a Phillips screwdriver to remove the shoulder screws from the door. Refrigerator Leveling and Door Closing The base grille covers the adjustable brake feet and roller assemblies located at the bottom of the refrigerator below the freezer drawer. Before making any adjustments, remove the base grille and move the refrigerator to its final location. Tools Needed: 1/4" hex driver Tools Provided: 1/8" hex key 1.  Use a 1/4" hex driver to remove both screws in base grille. 2.  Remove the base grille. Using both hands, grasp the grille firmly and pull it toward you. Open the freezer drawer to access the brake feet. NOTE: To allow the refrigerator to roll easier, raise the brake feet by turning them counterclockwise. The front rollers will be touching the floor. 4. Using a left-to-right motion, tighten the setscrew a quarter turn at a time just until setscrew begins to contact the shoulder screw. Do not fully tighten. 5.  Repeat steps 3 and 4 to fasten the right-hand setscrew to the shoulder screw. 6.  Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews. IMPORTANT: When the screws feel tight, tighten them an additional quarter turn. The handle is not properly installed without this extra tightening. 7.  Save the hex key and all instructions. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124

17
8.
Repeat steps 2 through 7 to install the other handle onto
the adjacent refrigerator door.
Freezer Drawer
1.
With the drawer closed, place the handle onto the shoulder
screws so that the setscrews are facing down toward the
floor.
A. Shoulder screw
B. Setscrews inside the handle
B
A
2.
Firmly push the handle toward the drawer until the handle
base is flush against the drawer.
3.
Insert the short end of the hex key into the left-hand hole
and slightly rotate the hex key until key is engaged in the
setscrew.
4.
Using a left-to-right motion, tighten the setscrew a quarter
turn at a time just until setscrew begins to contact the
shoulder screw. Do not fully tighten.
5.
Repeat steps 3 and 4 to fasten the right-hand setscrew to
the shoulder screw.
6.
Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT:
When the screws feel tight, tighten them an
additional quarter turn. The handle is not properly installed
without this extra tightening.
7.
Save the hex key and all instructions.
Remove the Handles
1.
While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is
engaged in the setscrew.
2.
Using a right-to-left motion, loosen the setscrew a quarter
turn at a time.
3.
Repeat steps 1 and 2 for the other setscrew. Slowly pull
the handle away from the door or drawer.
4.
If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
Refrigerator Leveling
and Door Closing
The base grille covers the adjustable brake feet and roller
assemblies located at the bottom of the refrigerator below the
freezer drawer. Before making any adjustments, remove the base
grille and move the refrigerator to its final location.
Tools Needed:
1/4" hex driver
Tools Provided:
1/8" hex key
1.
Use a 1/4" hex driver to remove both screws in base grille.
2.
Remove the base grille. Using both hands, grasp the grille
firmly and pull it toward you. Open the freezer drawer to
access the brake feet.
NOTE:
To allow the refrigerator to roll easier, raise the brake
feet by turning them counterclockwise. The front rollers will
be touching the floor.