Whirlpool WRS322FDAM Installation Guide - Page 17

PERFORMANCE DATA SHEET Water Filtration System Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters) System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of Live Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D. This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53. Substance Reduction Aesthetic Effects Chlorine Taste/Odor Particulate Class I* Contaminant Reduction Live Cysts† Asbestos Lead: @ pH 6.5 Lead: @ pH 8.5 Lindane Toxaphene Atrazine 2,4 - D NSF Reduction Requirements 50% reduction 85% reduction NSF Reduction Requirements 99.95% 99% 0.010 mg/L 0.010 mg/L 0.0002 mg/L 0.003 mg/L 0.003 mg/L 0.07 mg/L Average Influent 2.0 mg/L 7,300,000 #/mL Average Influent 160,000/L 87 MFL 0.160 mg/L 0.140 mg/L 0.0019 mg/L 0.014 mg/L 0.0094 mg/L 0.220 mg/L Influent Challenge Concentration 2.0 mg/L ± 10% At least 10,000 particles/mL Influent Challenge Concentration 50,000/L min. 107 to 108 fibers/L†† 0.15 mg/L ± 10% 0.15 mg/L ± 10% 0.002 mg/L ± 10% 0.015 mg/L ± 10% 0.009 mg/L ± 10% 0.210 mg/L ± 10% Maximum Effluent 0.20 mg/L 75,000 #/mL** Maximum Effluent 54/L† 0.17 MFL 0.001 mg/L 0.005 mg/L 0.00002 mg/L 0.001 mg/L 0.0005 mg/L 0.028 mg/L Minimum % Reduction 97 99 Minimum % Reduction 99.97 99 99.4 98.6 98.9 93 94.5 87.5 Average % Reduction 97.2 99.4 Average % Reduction 99.99 99 99.4 98.6 99 93 94.7 96.1 Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters). ■ It is important that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed. ■ Use replacement filter P4RFWB, part #W10295370A. 2013 suggested retail price of $39.99 U.S.A./$49.99 Canada. Prices are subject to change without notice. Style 1 - When the water filter status display changes from "GOOD" to "ORDER," order a new filter. When the filter indicator reads "REPLACE," it is recommended that you replace the filter. Style 2 - When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter. Style 3 - When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that you replace the filter. Style 4 - Press FILTER to check the status of your water filter. If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the filter. ■ After changing the water filter, flush the water system. See "Water and Ice Dispensers" or "Water Dispenser" in the User Instructions or User Guide. ■ These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary. ■ The product is for cold water use only. ■ The water system must be installed in compliance with state and local laws and regulations. ■ Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. ■ Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's name, address and telephone number. ■ Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's limited warranty. Application Guidelines/Water Supply Parameters Water Supply Water Pressure Water Temperature Service Flow Rate City or Well 30 - 120 psi (207 - 827 kPa) 33° - 100°F (0.6° - 37.8°C) 0.5 gpm (1.9 Lpm) @ 60 psi *Class I particle size: >0.5 to