Yamaha 03D Owner's Manual - Page 33

R with One DA-88 - mixing board

Get Yamaha 03D PDF manuals and user guides View all Yamaha 03D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

28 02R Applications 9 02R with One DA-88 This application shows how the 02R can be used with a Tascam DA-88 to create a 24-input, 8-track digital recording system. The eight digital tape returns and 24 Mic/Line inputs provide up to 32 inputs at mixdown. In addition, the 02R's built-in automation and scene memory systems provide both dynamic and static mix automation referenced to timecode. Connections • The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws out after installation as the card will not be grounded correctly. • The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape returns. • The DA-88 is connected to Slot [1] of the 02R. These tape inputs correspond to tracks one through eight. • The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track and can output SMPTE timecode or MTC. In addition, a timecode offset can be specified on the DA-88, so the 02R automix start time can be adjusted. The DA-88 also has the ability to re-stripe the timecode track. • The 75 ohm wordclock termination switch on the back of the 02R is set to ON. 02R Wordclock Setup On the DIGITAL I/O menu, the wordclock source should be set to W.CLK. DA-88 Wordclock Setup The DA-88 works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC cable. The sampling rate is set when the DA-88 tape is formatted. This can be either 48 kHz or 44.1 kHz. After formatting, the sampling rate is determined by the formatted tape. Notes • The DA-88 must be powered up even when it is not being used. Failure to do so may cause an intermittent pumping noise on the 02R. • On the DA-88 rear panel, set the MACHINE ID to 0. • The optional Tascam SY-88 Sync Board must be installed to use SMPTE timecode and MTC. This is available from Tascam. • The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON. • To use the MTC function, the SY-88 firmware must be version 3.08 or higher. • On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit recording applications. • Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m) are available from Tascam. Yamaha 02R & 03D Applications Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
28
02R Applications
Yamaha 02R & 03D Applications Guide
9
02R with One DA-88
This application shows how the 02R can be used with a Tascam DA-88 to create a 24-input,
8-track digital recording system. The eight digital tape returns and 24 Mic/Line inputs
provide up to 32 inputs at mixdown. In addition, the 02R’s built-in automation and scene
memory systems provide both dynamic and static mix automation referenced to timecode.
Connections
•
The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws
out after installation as the card will not be grounded correctly.
•
The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape
returns.
•
The DA-88 is connected to Slot
[1]
of the 02R. These tape inputs correspond to tracks
one through eight.
•
The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track
and can output SMPTE timecode or MTC. In addition, a timecode offset can be
specified on the DA-88, so the 02R automix start time can be adjusted. The DA-88 also
has the ability to re-stripe the timecode track.
•
The 75 ohm wordclock termination switch on the back of the 02R is set to ON.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
DA-88 Wordclock Setup
The DA-88 works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC
cable. The sampling rate is set when the DA-88 tape is formatted. This can be either 48 kHz
or 44.1 kHz. After formatting, the sampling rate is determined by the formatted tape.
Notes
•
The DA-88 must be powered up even when it is not being used. Failure to do so may
cause an intermittent pumping noise on the 02R.
•
On the DA-88 rear panel, set the MACHINE ID to 0.
•
The optional
Tascam SY-88 Sync Board
must be installed to use SMPTE timecode and
MTC. This is available from Tascam.
•
The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP
switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.
•
To use the MTC function, the SY-88
firmware
must be version 3.08 or higher.
•
On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is
the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit
recording applications.
•
Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m) are available
from Tascam.