Yamaha BD-S473 Owners Manual - Page 34

Picture, Sound, Problem, Possible causes and solutions - black

Get Yamaha BD-S473 PDF manuals and user guides View all Yamaha BD-S473 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Troubleshooting ■ Picture No picture. Problem Screen freezes and operation buttons do not work. Video is not output with the desired resolution. Wide-screen video appears vertically stretched, or black bands appear at the top and bottom of the screen. Or 4:3 video appears horizontally stretched. Square noise (mosaic) appears on the screen. Audio is not output, or images are not played back properly. ■ Sound Possible causes and solutions - Make sure that the HDMI cable is connected correctly. (p. 10) - Make sure that the connected TV or the AV receiver is set to the correct input. (p. 10) - With no disc inserted, or playback stopped, press and hold and on the front panel simultaneously to set video resolution to the default value. If a picture is still not output, press and hold seconds to switch NTSC/PAL. on the front panel for approximately 5 - Press , then restart playback. - Turn off the power and turn on the power again. - Press and hold p on the front panel for more than 5 seconds, and release to reset this Player. - Set to the desired resolution. (p. 26) - Change the aspect ratio of your TV. (p. 26) - Blocks in images may be visible in scenes with rapid movement due to the characteristics of digital image compression technology. - The audio may not be output or the images may not be played back properly for some discs in which copyright-protected contents are recorded. Problem No sound, or sound is distorted. Left and right channels of audio are reversed, or sound comes out of only one side. Audio is not output, or images are not played back properly. Cannot hear the sound of PIP (secondary audio). Possible causes and solutions - Check that the HDMI cable is connected correctly. (p. 10) - Turn the volume of TV or AV receiver up. - There is no sound during still mode, fast forward, and fast reverse. (p. 8) - Audio may not be output depending on the audio recording status, such as when audio other than an audio signal or non-standard audio is recorded for the audio content. (p. 3) - Check the HDMI connection. (p. 10) - The audio may not be output or the images may not be played back properly for some discs in which copyright-protected contents are recorded. - Set HDMI to PCM/Reencode. (p. 27) - To hear secondary audio, press 2ND AUDIO. (p. 6) - Depending on the disc, you may need to set secondary audio on the top menu of the disc. (p. 8) 32 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
32
En
Troubleshooting
■
Picture
■
Sound
Problem
Possible causes and solutions
No picture.
–
Make sure that the HDMI cable is connected correctly. (p. 10)
–
Make sure that the connected TV or the AV receiver is set to the correct input. (p. 10)
–
With no disc inserted, or playback stopped, press and hold
and
on the front
panel simultaneously to set video resolution to the default value.
If a picture is still not output, press and hold
on the front panel for approximately 5
seconds to switch NTSC/PAL.
Screen freezes and operation buttons
do not work.
– Press
, then restart playback.
–
Turn off the power and turn on the power again.
–
Press and hold
p
on the front panel for more than 5 seconds, and release to reset this
Player.
Video is not output with the desired
resolution.
–
Set to the desired resolution. (p. 26)
Wide-screen video appears vertically
stretched, or black bands appear at the
top and bottom of the screen. Or 4:3
video appears horizontally stretched.
–
Change the aspect ratio of your TV. (p. 26)
Square noise (mosaic) appears on the
screen.
–
Blocks in images may be visible in scenes with rapid movement due to the
characteristics of digital image compression technology.
Audio is not output, or images are not
played back properly.
–
The audio may not be output or the images may not be played back properly for some
discs in which copyright-protected contents are recorded.
Problem
Possible causes and solutions
No sound, or sound is distorted.
–
Check that the HDMI cable is connected correctly. (p. 10)
–
Turn the volume of TV or AV receiver up.
–
There is no sound during still mode, fast forward, and fast reverse. (p. 8)
–
Audio may not be output depending on the audio recording status, such as when audio
other than an audio signal or non-standard audio is recorded for the audio content. (p. 3)
Left and right channels of audio are
reversed, or sound comes out of only
one side.
–
Check the HDMI connection. (p. 10)
Audio is not output, or images are not
played back properly.
–
The audio may not be output or the images may not be played back properly for some
discs in which copyright-protected contents are recorded.
Cannot hear the sound of PIP
(secondary audio).
–
Set HDMI to PCM/Reencode. (p. 27)
–
To hear secondary audio, press
2ND AUDIO
. (p. 6)
–
Depending on the disc, you may need to set secondary audio on the top menu of the
disc. (p. 8)