Yamaha CLP-220 Owner's Manual - Page 35

Mount A., Secure A., Secure B and C., Connect the pedal cord., CAUTION

Get Yamaha CLP-220 PDF manuals and user guides View all Yamaha CLP-220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

33 ENGLISH 3. Mount A. CAUTION • Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. • Do not hold the keyboard in any position other than the position shown in the illustration. 3-1 Assemble the side panel protection (cardboard) pad, as shown in the illustration. Then, remove the two backing papers from the adhesive tape on the protection pad. 4. Secure A. 4-1 Secure A by tightening the short screws 2 (6 × 16mm) from the front. A 4-1 3-2 Cover the top of D and E with the side panel protection pad. Then, fix the protection pad with the adhesive tape. 3-3 Lower A horizontally while aligning a pin on the inner side of D and E with a bracket in the slot on the left and right side of A, then attach A to D and E securely. 3-3 5. Secure B and C. 5-1 Securely tighten the screws on the top of B that were attached in Step 2-2. 5-2 Securely tighten the screws on C that were attached in Step 1-3. 5-1 A 3-2 E D Place your hands at least 10 cm from either end of A when positioning it. 3-4 Remove the side panel protection pad. A BC 5-2 6. Connect the pedal cord. 6-1 Insert the pedal cord plug to the pedal connector from the rear. 6-2 Attach the cord holders to the rear panel as shown, then clip the cord into the holders. 6-3 Use a vinyl tie to take up any slack in the pedal cord. PEDAL 6-1 6-2 6-3 L L CLP-220 Keyboard Stand Assembly 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
CLP-220
Keyboard Stand Assembly
35
ENGLISH
3.
Mount A.
CAUTION
•
Fingers can become pinched between the main
unit and the rear or side panels, be extra careful
so as not to drop the main unit.
•
Do not hold the keyboard in any position other
than the position shown in the illustration.
3-1
Assemble the side panel protection (card-
board) pad, as shown in the illustration.
Then, remove the two backing papers from
the adhesive tape on the protection pad.
3-2
Cover the top of D and E with the side panel
protection pad. Then, fix the protection pad
with the adhesive tape.
3-3
Lower A horizontally while aligning a pin on
the inner side of D and E with a bracket in
the slot on the left and right side of A, then
attach A to D and E securely.
3-4
Remove the side panel protection pad.
4.
Secure A.
4-1
Secure A by tightening the short screws
2
(6
×
16mm) from the front.
5.
Secure B and C.
5-1
Securely tighten the screws on the top of B
that were attached in Step 2-2.
5-2
Securely tighten the screws on C that were
attached in Step 1-3.
6.
Connect the pedal cord.
6-1
Insert the pedal cord plug to the pedal con-
nector from the rear.
6-2
Attach the cord holders to the rear panel as
shown, then clip the cord into the holders.
6-3
Use a vinyl tie to take up any slack in the
pedal cord.
L
3-3
E
D
A
3-2
Place your hands
at least 10 cm
from either end
of A when
positioning it.
L
A
4-1
A
5-1
5-2
B
C
PEDAL
6-1
6-3
6-2
33