Yamaha CLP-811 Owner's Manual - Page 58
CLP-811 Assembly Procedure, Montage des CLP-811
View all Yamaha CLP-811 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 58 highlights
1 3 Four wide roundhead screws 1 Vier breite Rundkopfschrauben 1 Quatre grosses vis à tête ronde 1 Cuatro tornillos anchos de cabeza redonda 1 (6!20mm) Four tapered screws 4 Vier Senkkopfschrauben 4 Quatre vis pointues 4 Cuatro tornillos cónicos 4 (4!20mm) 2 Phone jacks Klinkenbuchsen Prises pour casque d'écoute Tomas de auriculares Styrofoam pads Styroporteile Coussinets en mousse Planchas de poliestireno Four wide flathead screws 2 Vier breite Flachkopfschrauben 2 Quatre grosses vis à tête plate 2 Cuatro tornillos anchos de cabeza plana 2 (6!20mm) Two short roundhead screws 5 Zwei kurze Rundkopfschrauben 5 Deux petites vis à tête ronde 5 Dos tornillos cortos de cabeza redonda 5 (4!12mm) Two thin flathead screws 3 Zwei dünne Flachkopfschrauben 3 Deux fines vis à tête plate 3 Dos tornillos finos de cabeza plana 3 (4!20mm) Two cord clamps 6 Zwei Kabelhalter 6 Deux pinces de fixation pour câbles 6 Dos bridas de cable 6 CLP-811 Assembly Procedure NOTE • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated above. Use of incorrect screws can cause damage. • Be sure to tighten up all screws upon completing assembly of each unit. • To disassemble, reverse the assembly sequence given below. 1 Have a Phillips-head screwdriver ready. 2 Open the box. Take out the two styrofoam pads and place them on the floor. Then take out main unit (A) and place it on top of the pads. NOTE Position the pads so as to protect the phone jacks on the base of the unit. 3 Remove all parts from the box. Confirm that all of the parts indicated above are present. 4 Fasten lower board (E) to the left and right sideboards. First, unravel the pedal cord bundled to the bottom of lower board (E). Then align the ends of lower board (E) with the right sideboard (C) and left sideboard (B). Finally, fasten in place with the four wide roundhead screws 1. Montage des CLP-811 HINWEIS • Achten Sie darauf, die Teile nicht zu verwechseln, und installieren Sie alle Teile in der richtigen Ausrichtung. Gehen Sie beim Zusammenbau bitte in der angegebenen Reihenfolge vor. • Die Montage sollte von mindestens zwei Personen vorgenommen werden. • Achten Sie darauf, die richtige Schraubengröße zu verwenden, wie es oben gezeigt ist. Die Verwendung der falschen Schrauben kann zu Schäden führen. • Achten Sie während der Montage darauf, bei jedem Arbeitsgang alle Schrauben festzuziehen. • Für die Demontage muß die angegebene Reihenfolge umgekehrt befolgt werden. 1 Halten Sie einen Kreuzschlitzschraubendreher bereit. 2 Öffnen Sie den Karton. Nehmen Sie die beiden Styroporteile heraus und legen Sie sie auf den Boden. Nehmen Sie dann die Haupteinheit (A) heraus, und legen Sie es auf die Styroporteile. HINWEIS Positionieren Sie die Styroporteile so, daß die Klinkenbuchsen am Boden des Gerätes geschützt sind. 3 Nehmen Sie alle Teile aus dem Karton. Sehen Sie nach, ob alle oben gezeigten Teile vorhanden sind. 4 Bringen Sie die Unterseite (E) an den linken und rechten Seitenteilen an. Lösen Sie dazu zunächst das Pedalkabel auf, das unten an der Unterseite zusammengebündelt ist (E). Richten Sie dann die Enden der Unterseite (E) mit dem rechten Seitenteil (C) und dem linken Seitenteil (B) aus. Schrauben Sie die Unterseite schließlich mit den vier breiten Rundkopfschrauben 1 fest. 54 CLP-811/611 CLP-811 Assembly Procedure/Montage des CLP-811/CLP-811 Montage Procédure/Montaje del modelo CLP-811