Yamaha S08 Owner's Manual - Page 80

Cannot find the Drum Voice., When using a controller or LFO, the effect is applied to undesired or

Get Yamaha S08 PDF manuals and user guides View all Yamaha S08 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Basics Section Quick Guide Reference Appendix Cannot find the Drum Voice. ● Drum Voices are selected differently than Normal Voices. (Page 30) Edits made to the Drum Voice have no effect. ● Has the Part Mode parameter been set correctly? (Page 22) Cannot play or edit drum voice sounds that are assigned to keys below A-1. ● Set Kbd Trans (CONTROLLER PAGE 4) to a negative value. (Page 67) Editing can't be done. ● Has the Category Search function been turned on? If Category Search is active, the Edit Mode can't be enabled. (Page 31) ● Have you selected a Wave (001 through 029, and 521) whose parameter settings are fixed? (Pages 59 and 68) ● Is the Utility mode or Controller mode active? ● For the Voice mode, are you attempting to edit? Remember that Chorus and Reverb effect settings are fixed for the Voices and cannot be changed. (Page 46) When using a controller or LFO, the effect is applied to undesired or unexpected parameters. ● Various parameters can be assigned simultaneously to be controlled by the modulation wheel, Assignable Controller 1 and the LFO. For those parameters you don't want to control, set the depth to "0." (Page 37) Cannot receive bulk data. ● When using the Voice Editor for S08, have you set a sufficient Dump Interval? The Dump Interval in the Voice Editor Setup dialog must be set to 10ms or greater. ● Has the Device Number parameter been set correctly? When receiving data with the S08's Bulk Dump function, you must set the S08 to the same device number as that specified on the transmitting device. (page 66) ● Has the Host Select parameter in Utility mode been set appropriately? (pages 13 to 15) Cannot properly receive or respond to data from the connected device. ● Has the Host Select parameter in Utility mode been set appropriately? (pages 13 to 15) ● Is either the Demo mode (page 16) or the Compare function (page 41) active? When either of these are active, incoming MIDI data is ignored. ● Is the MIDI cable intact and connected properly? 80 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Basics Section
Quick Guide
Reference
Appendix
80
Troubleshooting
Cannot find the Drum Voice.
●
Drum Voices are selected differently than Normal Voices.
(Page 30)
Edits made to the Drum Voice have no effect.
●
Has the Part Mode parameter been set correctly?
(Page 22)
Cannot play or edit drum voice sounds that are assigned
to keys below A-1.
●
Set Kbd Trans (CONTROLLER PAGE 4) to a negative value.
(Page 67)
Editing can’t be done.
●
Has the Category Search function been turned on?
If Category Search is active, the Edit Mode can’t be enabled.
(Page 31)
●
Have you selected a Wave (001 through 029, and 521) whose parameter settings are fixed?
(Pages 59 and 68)
●
Is the Utility mode or Controller mode active?
●
For the Voice mode, are you attempting to edit?
Remember that
Chorus and Reverb effect settings are fixed for the
Voices and cannot be changed.
(Page 46)
When using a controller or LFO, the effect is applied to undesired or
unexpected parameters.
●
Various parameters can be assigned simultaneously to be controlled by the modulation wheel, Assignable Controller 1
and the LFO.
For those parameters you don’t want to control, set the depth to “0.”
(Page 37)
Cannot receive bulk data.
●
When using the Voice Editor for S08, have you set a sufficient Dump Interval?
The Dump Interval in the Voice Editor
Setup dialog must be set to 10ms or greater.
●
Has the Device Number parameter been set correctly?
When receiving data with the S08’s Bulk Dump function, you
must set the S08 to the same device number as that specified on the transmitting device.
(page 66)
●
Has the Host Select parameter in Utility mode been set appropriately? (pages 13 to 15)
Cannot properly receive or respond to data from the connected
device.
●
Has the Host Select parameter in Utility mode been set appropriately? (pages 13 to 15)
●
Is either the Demo mode (page 16) or the Compare function (page 41) active?
When either of these are active, incoming
MIDI data is ignored.
●
Is the MIDI cable intact and connected properly?