ZyXEL PoE-12 User Guide - Page 2

ITALIANO Guida dell'utente PoE12-HP Iniettore PoE 802.3at Versione 1.00 Edizione 1, 4/2011 Contenuto della confezione • Una unità PoE12-HP • Una Guida dell'utente • Accessori per il montaggio a parete • Un cavo di alimentazione • Una scheda di garanzia Cenni generali Il PoE12-HP è un iniettore di alimentazione a una porta, progettato per essere utilizzato in reti Ethernet 10/100/1000 BaseT. El PoE inyecta corriente DC a través de los cables trenzados no usados de un cable estándar CAT 5 de 8 contactos. Esto aumenta la flexibilidad en el posicionamiento de un dispositivo con corriente sobre Ethernet (PoE) eliminando la necesidad de una fuente de alimentación cercana. Caratteristiche principali • Conforme agli standard IEEE802.3at e IEEE 802.3af. • Una porta RJ-45, porta PoE 10/100/1000 Mbps. • Consente di alimentare in modo costante un dispositivo PoE. • Rileva automaticamente se il dispositivo collegato è abilitato a PoE al fine di evitare di inviare corrente ad un dispositivo non-PoE. Collegamento del PoE12-HP Effettuare i collegamenti del PoE12-HP nel modo seguente. 3 PoE/DATA 2 Dispositivo PoE DATA 1 1 Dispositivo Ethernet 1. La porta DATA non trasmette elettricità. Utilizzare un cavo Ethernet per collegare la porta DATA del PoE12-HP alla porta LAN di un dispositivo Ethernet (come ad esempio uno switch Ethernet). 2. La porta PoE/DATA invia elettricità e dati Ethernet al dispositivo abilitato PoE. Utilizzare un cavo Ethernet passante diritto per collegare la porta PoE/DATA al dispositivo abilitato PoE. La lunghezza massima del cavo Ethernet e 100m. 3. Utilizzare il cavo di alimentazione in dotazione per collegare la presa di alimentazione ad una sorgente di alimentazione (presa a muro o ciabatta elettrica). • Il LED PWR diventa di colore verde quando il PoE12-HP è alimentato. LED Nella tabella seguente sono descritti i LED presenti sul PoE12-HP. LED PoE PWR Colore Verde Verde Stato Lampeg giante Acceso Acceso Spento Descrizione Il PoE12-HP sta rilevando il dispositivo PoE. È fornita alimentazione PoE. Il sistema è acceso. Il sistema è spento o ha un guasto. Montaggio a parete Attenersi alla procedura seguente per fissare il PoE12-HP alla parete. 1. Fissare le due viti fornite a corredo con il PoE12-HP nella parete, a una distanza di 106mm. Usare viti con testa da 6 a 8mm (0,24" 0,31"). Non avvitare completamente le viti nella parete, ma lasciare un piccolo spazio tra la testa della vite e il muro. 2. Lo spazio deve essere abbastanza grande da consentire alle teste delle viti di scorrere nelle apposite fessure e ai cavi di connessione di scorrere lungo la parte posteriore del PoE12-HP. Assicurarsi che le viti siano saldamente fissate alla parete e che siano abbastanza robuste per sostenere il peso del PoE12-HP con i cavi di collegamento. 3. Allineare i fori presso la parte posteriore di PoE12-HP con le viti sulla parete. Appendere il PoE12-HP sulle viti. È preferibile montare il PoE12-HP a parete in senso verticale, con la presa elettrica dal lato superiore. 106mm Risoluzione dei problemi Il LED PWR è spento e/o non viene fornita alimentazione al dispositivo abilitato PoE. • Controllare per verificare che il cavo di alimentazione sia collegato correttamente al PoE12-HP e ad una adeguata sorgente di alimentazione. Assicurarsi che la sorgente di alimentazione sia attiva e funzioni correttamente. • Fare riferimento alla sezione Collegamento del PoE12-HP. Controllare che i cavi Ethernet siano collegati correttamente e che venga usato il tipo corretto di cavo Ethernet. Se il problema persiste, contattare il proprio distributore locale. PoE12-HP 802.3at PoE 1.00 1, 4/2011 Ethernet 100 ɦ. 3 • PWR PoE12-HP PoE12-HP. PoE12-HP Ɉɛɡɨɪ PoE12-HP Ethernet 10/ 100/1000 BaseT 5 PoE12-HP PoE IEEE802.3at ɢ IEEE 802.3af 10/100/1000 Mbps RJ-45 ɞɥɹ PoE PoE PoE PoE12-HP PoE12-HP 3 PoE/DATA 2 1 PoE DATA 1 Ethernet 1 DATA Ethernet PoE12-HP ɩɨɪɬɚ DATA LAN (Ʌȼɋ) Ethernet Ethernet 2. ɉɨɪɬ PoE/DATA PoE Ethernet PoE PoE/DATA. ɐɜɟɬ PoE PoE12-HP PoE. PoE PWR PoE12-HP 1 PoE12-HP 106 6 ɦɦ ~ 8 ɦɦ (0.24" ~ 0.31 2 PoE12-HP PoE12-HP 3 PoE12-HP PoE12-HP PoE12-HP 106ɦɦ PWR PoE. PoE12-HP PoE12-HP Ethernet Ethernet ZyXEL ᜗᧯խ֮ PoE12-HP 802.3at PoE 墅ሽᕴ 1.00 ठ 2011 ‫ ڣ‬4 ִॣठ ฏխփ୲ PoE12-HP ᄗᥦ PoE12-HP power injector 10/100/1000 BaseT PoE12-HP 8 ൷ᆬ CAT 5 PoE IEEE802.3at ‫ ֗א‬IEEE 802.3af 10/100/1000 Mbps PoE ऱ RJ-45 PoE PoE PoE ᇘᆜΖ ຑ൷ PoE12-HP PoE12-HP LED PoE12-HP Ղऱ LED LED PoE ጸ‫ۥ‬ PWR ጸ‫ۥ‬ णኪ ᎅࣔ PoE12-HP PoE PoE ᕻ඀ PoE12-HP 1. ലࠟឍ PoE12-HP 106 mm 6 mm ~ 8 mm (0.24" ~ 0.31 2 PoE12HP PoE12-HP 3. ࠌ PoE12-HP PoE12-HP PoE12-HP 106mm 3 PoE/DATA 2 PoE ᇘᆜ DATA 1 1 1. DATA PoE12-HP ऱ DATA LAN 2. PoE/DATA PoE PoE/DATA PoE 100mΖ 3 PoE12-HP PWR LED ጊᣄඈᇞ PWR LED PoE ᇘᆜΖ PoE12-HP PoE12-HP Product Specifications Compatibility Ports LEDs Power Power Rating Power Consumption Weight

Dimensions Operating Environment Storage Environment EMI and Safety • IEEE802.3 10BASE-T • IEEE802.3u 100BASE-TX • IEEE802.3ab 1000BASE-T • IEEE802.3af • IEEE802.3at • One DATA port for connecting to the passive hub or switch • One PoE/DATA port for connecting to the PoE-enabled device 1 PoE (green)
1 PWR (green) Input: 1100~240V, 50~60Hz 100~240VAC 50/60Hz 1.5A max. 42.1W 396g
155 (W) * 74 (D) * 36 (H) mm Temperature: 0 ~ 50oC Humidity: 10 to 95% (non-condensing) Temperature: -40 ~ 70oC EN 60950-1, CSA international, FCC Part15 (Class B), CE EMC (Class B), RoHS Level A Safety Warnings • Do NOT use this product near water, for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. • Do NOT store things on the device. • Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. • Connect ONLY suitable accessories to the device. • Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. • Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). • Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. • Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. • If the power adaptor or cord is damaged, remove it from the device and the power source. • Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. • Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. • Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. • Make sure that the cable system is grounded so as to provide some protection against voltage surges. • Make sure to connect the cables to the correct ports. • Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately. Copyright Copyright © 2011 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Certifications Federal Communications Commission (FCC) Interference Statement The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. CE Mark Warning: This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Viewing Certifications Go to http://www.zyxel.com. Select your product on the ZyXEL home page to go to that product's page. Select the certification you wish to view from this page. ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser. To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the device at http://www.zyxel.com/web/ support_warranty_info.php. Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. ENGLISH Green Product Declaration RoHS Directive 2002/95/EC DEUTSCH Green Product Declaration RoHS Directive 2002/95/EC WEEE Directive 2002/96/EC (WEEE: Waste Electrical and Electronic Equipment) 2008/34/EC Declaration Signature: Name/Title: Raymond Huang / Quality & Customer Service Division Assistant VP Date (yyyy/mm/dd): 2011/1/24 ESPAÑOL Declaración de Producto Ecológico Directiva RoHS 2002/95/EC WEEE Directive 2002/96/EC (WEEE: Waste Electrical and Electronic Equipment) 2008/34/EC Unterschrift des Erklärenden: Name/Titel: Raymond Huang / Quality & Customer Service Division Assistant VP Datum (JJJJ/MM/TT): 2011/1/24 FRANÇAIS Déclaration de Produit Green Directive RoHS 2002/95/EC Directiva REEE 2002/96/EC (REEE : Residuos de Equipos Eléctricos y Electrónicos) 2008/34/EC Firma de declaración: Nombre/Título: Raymond Huang / Quality & Customer Service Division Assistant VP Fecha (aaaa/mm/dd): 2011/1/24 ITALIANO Dichiarazione Green Product Direttiva RoHS 2002/95/CE Directive DEEE 2002/96/EC (DEEE : Déchets des Equipements Electriques et Electroniques) 2008/34/EC Signature de la déclaration : Nom/Titre : Raymond Huang / Quality & Customer Service Division Assistant VP Date (aaaa/mm/jj) : 2011/1/24 NEDERLANDS Productmilieuverklaring RoHS-richtlijn 2002/95/EC Direttiva RAEE 2002/96/CE (RAEE: Rifiuti di Apparecchiature Elettriche ed Elettroniche) 2008/34/EC Firma dichiarazione: Nome/titolo: Raymond Huang / Quality & Customer Service Division Assistant VP Data (aaaa/mm/gg): 2011/1/24 SVENSKA Miljödeklaration RoHS Direktiv 2002/95/EC AEEA-richtlijn 2002/96/EC (AEEA: Afgedankte Elektrische en Elektronische Apparaten) 2008/34/EC Verklaringshandtekening: Naam/titel: Raymond Huang / Quality & Customer Service Division Assistant VP Datum(jjjj/mm/dd): 2011/1/24 WEEE Direktiv 2002/96/EC (WEEE: hantering av elektriskt och elektroniskt avfall) 2008/34/EC Deklaration undertecknad av: Namn/Titel: Raymond Huang / Quality & Customer Service Division Assistant VP Datum (åååå/mm/dd): 2011/1/24 Copyright C 2011 ZyXEL Communications Corporation