2013 Chrysler 300 User Guide - Page 18

2013 Chrysler 300 Manual

Page 18 highlights

G E T T I N G S TA R T E D • In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. These tether strap anchorages are under a plastic cover. • Loosen the child seat adjusters on the lower straps and tether straps so that you can attach the hook or connector to the lower and tether anchorages more easily. • Attach the lower hooks or connectors over the top of the seat cover material. • Then rotate the tether anchorage cover directly behind the seat where you are placing the child restrain and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restrain. • Tighten all three straps as you push the child restraint rearward and downward into the seat. • For center seating position route the tether strap over the seatback and adjustable headrest (with the headrest in the full down position) then attach the hook to the tether anchor located in the panel between the rear seatback and the rear window. Installing The Child Restraint Using The Vehicle Seat Belts • To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle. • Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. • Rotate the cover over the anchor directly behind the seat where you are placing the child restraint. These tether strap anchorages are under a plastic cover. • Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. • Attach the tether strap hook of the child restraint to the anchor and remove slack in the tether strap according to the child restraint manufacturer's instructions. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

• Inaddition,therearetetherstrapanchoragesbehindeachrearseatingpositionlocatedinthe
panelbetweentherearseatbackandtherearwindow.Thesetetherstrapanchoragesareunder
aplasticcover.
Loosen the child seat adjusters on the lower
strapsandtetherstrapssothatyoucanattach
thehookorconnectortothelowerandtether
anchoragesmoreeasily.
• Attach the lower hooks or connectors over
thetopoftheseatcovermaterial.
• Thenrotatethetetheranchoragecoverdi-
rectlybehindtheseatwhereyouareplacing
thechildrestrainandattachthetetherstrap
totheanchorage,beingcarefultoroutethe
tetherstraptoprovidethemostdirectpath
betweentheanchorandthechildrestrain.
• Tightenallthreestrapsasyoupushthechild
restraint rearward and downward into the
seat.
• Forcenterseatingpositionroutethetether
strap over the seatback and adjustable
headrest(withtheheadrestinthefulldown
position)thenattachthehooktothetether
anchorlocatedinthepanelbetweentherear
seatbackandtherearwindow.
InstallingTheChildRestraintUsingTheVehicleSeatBelts
• Toinstallachildrestraint,first,pullenoughoftheseatbeltwebbingfromtheretractortoroute
itthroughthebeltpathofthechildrestraintandslidethelatchplateintothebuckle.
• Next,extractalltheseatbeltwebbingoutoftheretractorandthenallowthebelttoretractinto
theretractor.Finally,pullonanyexcesswebbingtotightenthelapportionaroundthechild
restraint.Anyseatbeltsystemwillloosenwithtime,socheckthebeltoccasionally,andpullit
tightifnecessary.
• Rotate the cover over the anchor directly behind the seat where you are placing the child
restraint.Thesetetherstrapanchoragesareunderaplasticcover.
• Routethetetherstraptoprovidethemostdirectpathforthestrapbetweentheanchorandthe
childseat.
• Attachthetetherstraphookofthechildrestrainttotheanchorandremoveslackinthetether
strapaccordingtothechildrestraintmanufacturer’sinstructions.
GETTING STARTED
16