2013 Chrysler 300 User Guide - Page 86

2013 Chrysler 300 Manual

Get 2013 Chrysler 300 PDF manuals and user guides View all 2013 Chrysler 300 manuals

Page 86 highlights

W H AT TO D O I N E M E R G E N C I E S TIREFIT Usage Precautions • Replace the TIREFIT Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed on the bottle label) to assure optimum operation of the system. Refer to "Sealing a Tire with TIREFIT" section (F) "Sealant Bottle and Hose Replacement". • The Sealant Bottle (1) and Sealant Hose (6) are a one tire application use. After each use, always replace these components immediately at an authorized dealer. • When the TIREFIT sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the TIREFIT kit. • You can use the TIREFIT air pump to inflate bicycle tires. The kit also comes with two needles, located in the Accessory Storage Compartment (on the bottom of the air pump) for inflating sport balls, rafts, or similar inflatable items. However, use only the Air Pump Hose (7) and make sure the Mode Select Knob (5) is in the Air Mode when inflating such items to avoid injecting sealant into them. The TIREFIT Sealant is only intended to seal punctures less than 1/4 in (6 mm) diameter in the tread of your vehicle. • Do not lift or carry the TIREFIT kit by the hoses. Sealing A Tire With TIREFIT (A) Whenever You Stop To Use TIREFIT: 1. Pull over to a safe location and turn on the vehicle's Hazard Warning flashers. 2. Verify that the valve stem (on the wheel with the deflated tire) is in a position that is near to the ground. This will allow the TIREFIT Hoses (6) and (7) to reach the valve stem and keep the TIREFIT kit flat on the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in PARK (auto transmission) or in Gear (manual transmission) and turn Off the ignition. 4. Set the parking brake. (B) Setting Up To Use TIREFIT: 1. Turn the Mode Select Knob (5) to the Sealant Mode position. 2. Uncoil the Sealant Hose (6) and then remove the cap from the fitting at the end of the hose. 3. Place the TIREFIT kit flat on the ground next to the deflated tire. 4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 5. Uncoil the Power Plug (8) and insert the plug into the vehicle's 12 Volt power outlet. 6. Do not remove foreign objects (e.g., screws or nails) from the tire. 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
TIREFITUsagePrecautions
• Replace the TIREFIT Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date
(printedonthebottlelabel)toassureoptimumoperationofthesystem.Referto“Sealinga
TirewithTIREFIT”section(F)“SealantBottleandHoseReplacement”.
• The Sealant Bottle (1) and Sealant Hose (6) are a one tire application use. After each use,
alwaysreplacethesecomponentsimmediatelyatanauthorizeddealer.
• WhentheTIREFITsealantisinaliquidform,cleanwater,andadampclothwillremovethe
materialfromthevehicleortireandwheelcomponents.Oncethesealantdries,itcaneasilybe
peeledoffandproperlydiscarded.
• For optimum performance, make sure the valve stem on the wheel is free of debris before
connectingtheTIREFITkit.
• YoucanusetheTIREFITairpumptoinflatebicycletires.Thekitalsocomeswithtwoneedles,
locatedintheAccessoryStorageCompartment(onthebottomoftheairpump)forinflating
sportballs,rafts,orsimilarinflatableitems.However,useonlytheAirPumpHose(7)andmake
suretheModeSelectKnob(5)isintheAirModewheninflatingsuchitemstoavoidinjecting
sealantintothem.TheTIREFITSealantisonlyintendedtosealpunctureslessthan1/4in
(6mm)diameterinthetreadofyourvehicle.
• DonotliftorcarrytheTIREFITkitbythehoses.
SealingATireWithTIREFIT
(A)WheneverYouStopToUseTIREFIT:
1. Pullovertoasafelocationandturnonthevehicle’sHazardWarningflashers.
2. Verifythatthevalvestem(onthewheelwiththedeflatedtire)isinapositionthatisneartothe
ground.ThiswillallowtheTIREFITHoses(6)and(7)toreachthevalvestemandkeepthe
TIREFITkitflatontheground.Thiswillprovidethebestpositioningofthekitwheninjecting
thesealantintothedeflatedtireandrunningtheairpump.Movethevehicleasnecessaryto
placethevalvesteminthispositionbeforeproceeding.
3. PlacethetransmissioninPARK(autotransmission)orinGear(manualtransmission)andturn
Offtheignition.
4. Settheparkingbrake.
(B)SettingUpToUseTIREFIT:
1. TurntheModeSelectKnob(5)totheSealantModeposition.
2. UncoiltheSealantHose(6)andthenremovethecapfromthefittingattheendofthehose.
3. PlacetheTIREFITkitflatonthegroundnexttothedeflatedtire.
4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant
Hose(6)ontothevalvestem.
5. UncoilthePowerPlug(8)andinserttheplugintothevehicle’s12Voltpoweroutlet.
6. Donotremoveforeignobjects(e.g.,screwsornails)fromthetire.
WHAT TO DO IN EMERGENCIES
84