2011 Dodge Nitro User Guide - Page 39

2011 Dodge Nitro Manual

Page 39 highlights

ELECTRONICS • Wait for the "ready" prompt and BEEP. • (After the BEEP), say "Uconnect setup". • (After the BEEP), say "phone pairing". • (After the BEEP), say "pair a phone". • Follow the audible prompts. • You will be asked to enter a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. • You will then be prompted to give the phone pairing a name (each phone paired should have a unique name). • Next you will be asked to give this new pairing a priority of 1 thru 7 (up to seven phones may be paired); 1 is the highest and 7 is the lowest priority. The system will only connect to the highest priority phone that exists within the proximity of the vehicle. Making A Phone Call • Press the Phone button . • (After the BEEP), say "dial" (or "call" a name). • (After the BEEP), say number (or name). Phonebook Edit • Press the Phone button . • (After the BEEP), say "phonebook". • (After the BEEP), say "new entry" or "list names" or "delete". • Follow the prompts. Receiving A Call - Accept (And End) • When an incoming call rings/is announced on Uconnect™, press the Phone button . • To end a call, press the Phone button . Mute (Or Unmute) Microphone During Call • During a call, press the Voice Command button • (After the BEEP), say "mute" (or "mute off"). . Transfer Ongoing Call Between Handset And Vehicle • During a call, press the Voice Command button • (After the BEEP), say "transfer call". . Changing The Volume • Start a dialogue by pressing the Phone button a normal call. , then adjust the volume during 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84

• Wait for the “ready” prompt and BEEP.
• (After the BEEP), say “Uconnect setup”.
• (After the BEEP), say “phone pairing”.
• (After the BEEP), say “pair a phone”.
• Follow the audible prompts.
• You will be asked to enter a four-digit Personal Identification Number (PIN), which
you will later need to enter into your mobile phone. You can enter any four-digit
PIN. You will not need to remember this PIN after the initial pairing process.
• You will then be prompted to give the phone pairing a name (each phone paired
should have a unique name).
• Next you will be asked to give this new pairing a priority of 1 thru 7 (up to seven
phones may be paired); 1 is the highest and 7 is the lowest priority. The system
will only connect to the highest priority phone that exists within the proximity of
the vehicle.
MakingAPhoneCall
• Press the Phone button
.
• (After the BEEP), say “dial” (or “call” a name).
• (After the BEEP), say number (or name).
PhonebookEdit
• Press the Phone button
.
• (After the BEEP), say “phonebook”.
• (After the BEEP), say “new entry” or “list names” or “delete”.
• Follow the prompts.
ReceivingACall–Accept(AndEnd)
• When an incoming call rings/is announced on Uconnect™, press the Phone
button
.
• To end a call, press the Phone button
.
Mute(OrUnmute)MicrophoneDuringCall
• During a call, press the Voice Command button
.
• (After the BEEP), say “mute” (or “mute off”).
TransferOngoingCallBetweenHandsetAndVehicle
• During a call, press the Voice Command button
.
• (After the BEEP), say “transfer call”.
ChangingTheVolume
• Start a dialogue by pressing the Phone button
, then adjust the volume during
a normal call.
ELECTRONICS
37