2013 Ford F250 Super Duty Super Cab Diesel Supplement Printing 1 - Page 40

2013 Ford F250 Super Duty Super Cab Manual

Get 2013 Ford F250 Super Duty Super Cab PDF manuals and user guides View all 2013 Ford F250 Super Duty Super Cab manuals

Page 40 highlights

Fuel and Refueling Optional information display procedure 1. Start with the vehicle engine fully warmed. 2. From the main menu, select Gauge Mode and scroll through until one of the following options appear: • If the DPF needs cleaning and the vehicle is warmed up, you will be prompted to hold OK to clean Exhaust xx% Full or Exhaust Filter Full. Press OK and then follow the prompts regarding exhaust position as needed to initiate OCR. Be sure to understand each prompt. If you are not sure what is being asked by each prompt, contact your authorized dealer. The display will confirm the operation has started and when it has finished. • When the exhaust system is overloaded cleaning will be allowed until a certain saturation level. If the vehicle is warmed up and ready the powertrain fault indicator will illuminate and you will be prompted to hold OK to clean Drive to Clean Exhaust System + Exhaust Filter Overloaded . Press OK and then follow the prompts regarding exhaust position as needed to initiate OCR. Be sure to understand each prompt. If you are not sure what is being asked by each prompt, contact your authorized dealer. The display will confirm the operation has started and when it has finished. You can also drive to clean the filter. See Active regeneration earlier in this chapter. • The service engine soon light will illuminate and the following messages Exhaust Filter Overloaded + Reduced Engine Power or Reduced Engine Power will appear when the system is at the point of oversaturation you will not be able to allow cleaning . The vehicle must be serviced by an authorized dealer. 3. Once OCR starts, the engine's rpm will rise to approximately 2,000 2,400 rpm and the cooling fan will increase speed; you will hear a change in audible sound due to the fan and engine speed increase. It is not necessary to open the hood on the engine compartment. Once OCR is complete, the engine rpm and fan will return to normal idling. The exhaust system will remain very hot for several minutes even after regeneration is complete. Do not reposition the vehicle over materials that could burn until the exhaust system has had sufficient time to cool. Depending on the amount of soot collected by the DPF, ambient temperature, and altitude, OCR may last from 10 to 25 minutes. 39 2013 Diesel (67l) Supplement, 1st Printing USA (fus)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Optional information display procedure
1. Start with the vehicle engine fully warmed.
2. From the main menu, select Gauge Mode and scroll through until one
of the following options appear:
•
If the DPF needs cleaning and the vehicle is warmed up, you will be
prompted to hold OK to clean
Exhaust xx% Full
or
Exhaust Filter
Full
. Press OK and then follow the prompts regarding exhaust
position as needed to initiate OCR. Be sure to understand each
prompt. If you are not sure what is being asked by each prompt,
contact your authorized dealer. The display will confirm the operation
has started and when it has finished.
•
When the exhaust system is
overloaded cleaning will be
allowed until a certain saturation
level. If the vehicle is warmed up and ready the powertrain fault
indicator will illuminate and you will be prompted to hold OK to clean
Drive to Clean Exhaust System
+
Exhaust Filter Overloaded
.
Press OK and then follow the prompts regarding exhaust position as
needed to initiate OCR. Be sure to understand each prompt. If you are
not sure what is being asked by each prompt, contact your authorized
dealer. The display will confirm the operation has started and when it
has finished. You can also drive to clean the filter. See
Active
regeneration
earlier in this chapter.
•
The service engine soon light will
illuminate and the following
messages
Exhaust Filter
Overloaded
+
Reduced Engine Power
or
Reduced Engine Power
will appear when the system is at the point of oversaturation you will
not be able to allow cleaning . The vehicle must be serviced by an
authorized dealer.
3. Once OCR starts, the engine’s rpm will rise to approximately 2,000 -
2,400 rpm and the cooling fan will increase speed; you will hear a change
in audible sound due to the fan and engine speed increase.
It is not necessary to open the hood on the engine compartment. Once
OCR is complete, the engine rpm and fan will return to normal idling.
The exhaust system will remain very hot for several minutes even after
regeneration is complete. Do not reposition the vehicle over materials
that could burn until the exhaust system has had sufficient time to
cool. Depending on the amount of soot collected by the DPF, ambient
temperature, and altitude, OCR may last from 10 to 25 minutes.
Fuel and Refueling
39
2013 Diesel
(67l)
Supplement, 1st Printing
USA
(fus)