2014 Lincoln Navigator L Quick Reference Guide Printing 1 - Page 6

Convenience Rain-sensing Wipers If activated, your wipers will automatically turn on when moisture is present on the windshield. The wipers will not cycle until moisture is detected on the windshield, and the wiper speed will vary based on the amount of moisture detected on the windshield and the sensitivity setting. The wipers will continue to wipe as long as moisture is detected. To deactivate, turn your wiper controls off. Note: Make sure that this feature is turned off before entering a car wash. Comfort Power Liftgate 3.  To close using the rear cargo area button: Press and release the control located on the left rear quarter panel. This button is automatically disabled when the liftgate is latched. Note: Keep clear of the liftgate when operating the rear switch. Your power liftgate is equipped with an obstacle detection feature which will either stop or revert to a full open position if it encounters a solid object. For complete information, see the Liftgate section within the Locks chapter of your Owner's Manual. you. The pedals should only be adjusted when the vehicle is stopped and in P (Park). 2014 NAVIGATOR PowerFold® Third-row Seat* 3.  To return the seatback to its original position, press "UP" on the button. Note: The power-folding seats will operate for 10 minutes after the ignition switch is turned off. The transmission must be in P (Park) and the liftgate or liftgate glass must be open. Second-row Heated Seats Memory Seat Feature The memory function will save and recall the positions of the driver seat, power mirrors, adjustable pedals and steering column. Use the control located on the side of the driver's seat to program and then recall saved memory positions. SecuriCodeTM Keyless Entry Keypad Press on the instrument panel to open or close the power liftgate. For added convenience, there are three more ways to activate your power liftgate's capabilities: 1.  On your remote entry twice transmitter, press within three seconds to open or close your power liftgate. 2.  To open using the liftgate control button in the liftgate handle: Unlock the doors using either the remote entry transmitter or the power door unlock control, and press the control. MyKey® MyKey allows you to program certain driving restrictions in order to promote good driving habits. You can set speed restrictions and limit volume levels. For complete information, refer to the MyKey chapter in your Owner's Manual. 10 Power-Adjustable Foot Pedals Located to the left of your steering column, your poweradjustable pedal control lets you move your brake and accelerator pedals closer. Press the arrow to move the pedals closer to you or the arrow to move the pedals further away from Lock or unlock the doors or release the liftgate glass without using a key. The keypad can be operated with the factory-set, 5-digit entry code; this code is located on the owner's wallet card in the glove box. You can also create up to five of your own 5-digit personal entry codes. To lock all of the doors and liftgate, press and hold 7•8 and 9•0 at the same time. For complete information, refer to the Locks chapter of your Owner's Manual. 60/40 split-folding bench seat uses a power-activated seatback release. Fold one side or both down for more flexibility. The controls are located on the right-hand rear quarter trim panel that is accessible from the liftgate area. Note: Make sure all seatbelts are unfastened. To lower: 1. M  ake sure that the head restraints are folded down first. 2. Press "FOLD" on the button. Front Heated and Ventilated Seats The rear heated seat controls are located on the rear of the center console. Press the indicated side of the control for maximum heat. Press again to deactivate. Press the indicated side of the control for minimum heat. Press again to deactivate. Note: The heated seats reset at every ignition run cycle. They will turn off automatically when the engine is turned off. Press the heated seat symbol or the ventilated seat symbol to cycle through the various settings and off. Warmer or cooler settings are indicated by more indicator lights. To program position 1, switch the ignition on. Move the memory features to your preferred position. Press and hold the 1 button for about two seconds until you hear a tone. Use this same procedure to set the second position by using the 2 button . You can now use these controls to recall the set memory positions. *if equipped 11