2016 Polaris Ranger 570 EPS Owners Manual - Page 77

2016 Polaris Ranger 570 EPS Manual

Get 2016 Polaris Ranger 570 EPS PDF manuals and user guides View all 2016 Polaris Ranger 570 EPS manuals

Page 77 highlights

MAINTENANCE POLARIS Variable Transmission (PVT) System PVT Drying There may be some instances when water is ingested into the PVT system. Use the following instructions to dry it out before operating. 1. Position the vehicle on a level surface. 2. Remove the red drain plug on the outer clutch cover. Allow the water to drain completely. Reinstall the drain plug. 3. Place the transmission in PARK. 4. Start the engine. 5. Apply varying throttle for 10-15 seconds to expel the moisture and air-dry the belt and clutches. Do not hold the throttle wide open for more than five (5) seconds. Drain Plug 6. Allow the engine RPM to settle to idle speed. Apply the brakes. Shift the transmission to the lowest available range. 7. Test for belt slippage. If the belt slips, repeat the process. 8. Your vehicle requires service as soon as possible. Your POLARIS dealer can assist. Vehicle Immersion NOTICE: If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle in for service before starting the engine. Your POLARIS dealer can provide this service. If it's impossible to take your RANGER to a dealer before starting it, follow the steps outlined below. 1. Move the vehicle to dry land or at the very least, to water below the footrests. 2. Dry any water present in the air box. Filter replacement is required if water is present. 3. Remove the spark plugs. Turn the engine over several times using the electric start. 4. Dry the spark plugs and reinstall, or replace with new plugs. 5. Attempt to start the engine. If necessary, repeat the drying procedure. 6. Take the vehicle in for service as soon as possible, whether you succeed in starting it or not. Your POLARIS dealer can provide the required service. 7. If water has been ingested into the PVT follow the procedure on page 75 for drying. 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
75
MAINTENANCE
POLARIS Variable Transmission (PVT) System
PVT Drying
There may be some instances when water is ingested into the PVT system. Use the following
instructions to dry it out before operating.
1.
Position the vehicle on a level surface.
2.
Remove the red drain plug on the outer clutch
cover. Allow the water to drain completely.
Reinstall the drain plug.
3.
Place the transmission in PARK.
4.
Start the engine.
5.
Apply varying throttle for 10-15 seconds to
expel the moisture and air-dry the belt and
clutches. Do not hold the throttle wide open
for more than five (5) seconds.
6.
Allow the engine RPM to settle to idle speed.
Apply the brakes. Shift the transmission to
the lowest available range.
7.
Test for belt slippage. If the belt slips, repeat the process.
8.
Your vehicle requires service as soon as possible. Your POLARIS dealer can assist.
Vehicle Immersion
NOTICE:
If your vehicle becomes immersed, major engine damage can result if the machine is not
thoroughly inspected. Take the vehicle in for service before starting the engine. Your
POLARIS dealer can provide this service.
If it's impossible to take your
RANGER
to a dealer before starting it, follow the steps outlined
below.
1.
Move the vehicle to dry land or at the very least, to water below the footrests.
2.
Dry any water present in the air box. Filter replacement is required if water is present.
3.
Remove the spark plugs. Turn the engine over several times using the electric start.
4.
Dry the spark plugs and reinstall, or replace with new plugs.
5.
Attempt to start the engine. If necessary, repeat the drying procedure.
6.
Take the vehicle in for service as soon as possible, whether you succeed in starting it or
not. Your POLARIS dealer can provide the required service.
7.
If water has been ingested into the PVT follow the procedure on page 75 for drying.
Drain Plug