2008 Yamaha Motorsports FX Nytro MTX Owners Manual - Page 22

2008 Yamaha Motorsports FX Nytro MTX Manual

Get 2008 Yamaha Motorsports FX Nytro MTX PDF manuals and user guides View all 2008 Yamaha Motorsports FX Nytro MTX manuals

Page 22 highlights

Control functions 1. Grip/thumb warmer adjustment switch To raise the temperature To raise the grip warmer temperature, press the " " side of the switch. To raise the thumb warmer temperature, press the " " side of the switch. To lower the temperature Continue to press the switch until the temperature level returns to the minimum level, and then raise the temperature to the desired level. ESU10690 1. Auxiliary DC jack cap 2. Auxiliary DC jack NOTE: After using the auxiliary DC jack, be sure to remove the accessory power plug from the jack and close the auxiliary DC jack cap. ECS00120 CAUTION: G Auxiliary DC jack (FX10MT / FX10MTR / FX10MTRA) The auxiliary DC jack is located in the front panel and can be used for accessories. G NOTE: The auxiliary DC jack cannot be used if the engine is not running. To use the auxiliary DC jack 1. Start the engine. 2. Open the auxiliary DC jack cap, and then insert the accessory power plug into the jack. Do not use accessories requiring more than the maximum rated capacity for the auxiliary DC jack. This may overload the circuit and cause the fuse to blow. (See page 67 for the specified amperage.) Do not use an automotive cigarette lighter or other accessory with a plug that gets hot because the jack can be damaged. Maximum rated capacity: DC 12 V, 2.5 A (30 W) ESU10560 Brake lever The snowmobile is stopped by braking the entire drive system. Squeeze the brake lever towards the handlebar grip to stop the snowmobile. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Control functions
16
To raise the temperature
To raise the grip warmer temperature, press
the “
” side of the switch. To raise the thumb
warmer temperature, press the “
” side of
the switch.
To lower the temperature
Continue to press the switch until the temper-
ature level returns to the minimum level, and
then raise the temperature to the desired lev-
el.
ESU10690
Auxiliary DC jack (FX10MT /
FX10MTR / FX10MTRA)
The auxiliary DC jack is located in the front
panel and can be used for accessories.
NOTE:
The auxiliary DC jack cannot be used if the
engine is not running.
To use the auxiliary DC jack
1.
Start the engine.
2.
Open the auxiliary DC jack cap, and then
insert the accessory power plug into the
jack.
NOTE:
After using the auxiliary DC jack, be sure to
remove the accessory power plug from the
jack and close the auxiliary DC jack cap.
CAUTION:
ECS00120
●
Do not use accessories requiring more
than the maximum rated capacity for the
auxiliary DC jack. This may overload the
circuit and cause the fuse to blow. (See
page 67 for the specified amperage.)
●
Do not use an automotive cigarette light-
er or other accessory with a plug that
gets hot because the jack can be dam-
aged.
ESU10560
Brake lever
The snowmobile is stopped by braking the en-
tire drive system.
Squeeze the brake lever towards the handle-
bar grip to stop the snowmobile.
1.
Grip/thumb warmer adjustment switch
1.
Auxiliary DC jack cap
2.
Auxiliary DC jack
Maximum rated capacity:
DC 12 V, 2.5 A (30 W)