2010 Yamaha Motorsports Apex Owners Manual - Page 25

2010 Yamaha Motorsports Apex Manual

Get 2010 Yamaha Motorsports Apex PDF manuals and user guides View all 2010 Yamaha Motorsports Apex manuals

Page 25 highlights

Control functions 3. After using the auxiliary DC jack, be sure to remove the accessory power plug from the jack and to close the auxiliary DC jack cap. 1 2 ECS01002 NOTICE G G To avoid circuit overload and a possible fuse blowing, do not use accessories requiring more than the maximum rated capacity for the auxiliary DC jack. RX10R / RX10LT: Do not connect accessories with a combined requirement of more than 30 W to the auxiliary DC jack and helmet shield heater jack. (See page 74 for the specified fuse amperage.) Do not use an automotive cigarette lighter or other accessory with a plug that gets hot because the jack can be damaged. Maximum rated capacity: DC 12 V, 2.5 A (30 W) 1. Helmet shield heater jack cap 2. Helmet shield heater jack 3. After using the helmet shield heater, be sure to remove its power plug from the jack and to close the jack cap. ECS01010 NOTICE To avoid circuit overload and a possible fuse blowing, do not use a helmet shield heater requiring more than the maximum rated capacity for the helmet shield heater jack and, when using both the auxiliary DC jack and helmet shield heater jack, do not use accessories requiring a combined total of more than 30 W. Maximum rated capacity: DC 12 V, 1.5 A (18 W) ESU13522 ESU13690 Helmet shield heater jack (RX10R / RX10LT) The helmet shield heater jack is located on the left side of the handlebar. TIP The helmet shield heater jack can only be used if the engine is running. To use the helmet shield heater jack 1. Start the engine. 2. Open the helmet shield heater jack cap, and then insert the power plug of the helmet shield heater into the jack. Brake lever The snowmobile is stopped by braking the entire drive system. Squeeze the brake lever towards the handlebar grip to stop the snowmobile. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Control functions
19
3.
After using the auxiliary DC jack, be sure
to remove the accessory power plug from
the jack and to close the auxiliary DC jack
cap.
NOTICE
ECS01002
●
To avoid circuit overload and a possible
fuse blowing, do not use accessories re-
quiring more than the maximum rated
capacity for the auxiliary DC jack.
RX10R / RX10LT: Do not connect acces-
sories with a combined requirement of
more than 30 W to the auxiliary DC jack
and helmet shield heater jack.
(See page 74 for the specified fuse am-
perage.)
●
Do not use an automotive cigarette light-
er or other accessory with a plug that
gets hot because the jack can be dam-
aged.
ESU13690
Helmet shield heater jack
(RX10R / RX10LT)
The helmet shield heater jack is located on
the left side of the handlebar.
TIP
The helmet shield heater jack can only be
used if the engine is running.
To use the helmet shield heater jack
1.
Start the engine.
2.
Open the helmet shield heater jack cap,
and then insert the power plug of the hel-
met shield heater into the jack.
3.
After using the helmet shield heater, be
sure to remove its power plug from the
jack and to close the jack cap.
NOTICE
ECS01010
To avoid circuit overload and a possible
fuse blowing, do not use a helmet shield
heater requiring more than the maximum
rated capacity for the helmet shield heater
jack and, when using both the auxiliary DC
jack and helmet shield heater jack, do not
use accessories requiring a combined to-
tal of more than 30 W.
ESU13522
Brake lever
The snowmobile is stopped by braking the en-
tire drive system.
Squeeze the brake lever towards the handle-
bar grip to stop the snowmobile.
Maximum rated capacity:
DC 12 V, 2.5 A (30 W)
1.
Helmet shield heater jack cap
2.
Helmet shield heater jack
Maximum rated capacity:
DC 12 V, 1.5 A (18 W)
1
2