3Com 3C13701 Installation Guide - Page 45

Powering On the Router

Get 3Com 3C13701 PDF manuals and user guides View all 3Com 3C13701 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Startup of the Router 45 2 Set the serial interface parameters. As shown in Figure 38, in the properties dialog box of the serial interface, set the baud rate to 9600, data bit to 8, no parity check, stop bit to 1, and flow control to none. Then, click to return to the HyperTerminal window. Figure 38 Setting serial interface parameters 3 Set HyperTerminal properties. Select [Properties\Port Settings] in the HyperTerminal to enter the properties setting window. Select the terminal emulation type to be VT100 or Auto detect, and click to return to the HyperTerminal window. Powering On the Router Checking Before Power-On Check according to the following items before powering on the router. ■ Whether the power cord and PGND wire are correctly connected. ■ Whether the voltage of the power supply complies with the requirement of the router. ■ Whether the console cable is correctly connected, whether the PC or terminal for configuration is open, and whether the settings are done. WARNING: Before powering on the router, be aware of where the power supply switch to the router is located, so that the power supply can be disconnected quickly if a accident should occur. Powering On the Router ■ Turn on the site power. ■ Turn on the power switch of the router.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Startup of the Router
45
2
Set the serial interface parameters. As shown in Figure 38, in the properties dialog box of
the serial interface, set the baud rate to 9600, data bit to 8, no parity check, stop bit to
1, and flow control to none. Then, click <OK> to return to the HyperTerminal window.
Figure 38
Setting serial interface parameters
3
Set HyperTerminal properties. Select [Properties\Port Settings] in the HyperTerminal to
enter the properties setting window. Select the terminal emulation type to be VT100 or
Auto detect, and click <OK> to return to the HyperTerminal window.
Powering On the
Router
Checking Before Power-On
Check according to the following items before powering on the router.
■
Whether the power cord and PGND wire are correctly connected.
■
Whether the voltage of the power supply complies with the requirement of the
router.
■
Whether the console cable is correctly connected, whether the PC or terminal for
configuration is open, and whether the settings are done.
WARNING:
Before powering on the router, be aware of where the power supply switch to
the router is located, so that the power supply can be disconnected quickly if a accident
should occur.
Powering On the Router
■
Turn on the site power.
■
Turn on the power switch of the router.