3Com 3C515-TRIROM User Guide - Page 20

Connect the other end of the network cable to a, 10BASE-T or a 100BASE-TX network port., Check

Get 3Com 3C515-TRIROM - Ethernet/Fast Ethernet MBA Managed PC Boot Agent ROM PDF manuals and user guides
UPC - 662705125800
View all 3Com 3C515-TRIROM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

2-6 CHAPTER 2: INSTALLING THE NIC 100 L 10 N K ACT TX TX 100 LNK LED 10 LNK LED ACT LED RJ-45 port RJ-45 connector Figure 2-5 Connecting the Network Cable to the RJ-45 Connector 2 Connect the other end of the network cable to a 10BASE-T or a 100BASE-TX network port. 3 Check the LEDs, shown in Figure 2-5. After installation, and before you install the network driver, the LEDs indicate the following: s 10 LNK LED lights green to show 10 Mbps link integrity. s 100 LNK lights green to show 100 Mbps link integrity. s ACT LED is OFF until the network driver is installed and then lights yellow to indicate port traffic for either speed. For information on what the LEDs indicate after the network driver is loaded, see Table 5-1. The next step is to load the network driver. See Chapter 3 for Novell NetWare driver information and Chapter 4 for NDIS network driver information. Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
2-6
C
HAPTER
2: I
NSTALLING
THE
NIC
Figure 2-5
Connecting the Network Cable to the RJ-45 Connector
2
Connect the other end of the network cable to a
10BASE-T or a 100BASE-TX network port.
3
Check the LEDs, shown in Figure 2-5.
After installation, and before you install the network
driver, the LEDs indicate the following:
■
10 LNK LED lights green to show 10 Mbps
link integrity.
■
100 LNK lights green to show 100 Mbps link integrity.
■
ACT LED is OFF until the network driver is installed
and then lights yellow to indicate port traffic for
either speed.
For information on what the LEDs indicate after the
network driver is loaded, see Table 5-1.
The next step is to load the network driver. See Chapter 3
for Novell NetWare driver information and Chapter 4 for
NDIS network driver information.
RJ-45 port
RJ-45
connector
100 LNK LED
10 LNK LED
ACT LED
100
TX
TX
L
N
K
10
ACT
Downloaded from
www.Manualslib.com
manuals search engine