3M X55 Operation Guide - Page 42

3M X55 Manual

Get 3M X55 PDF manuals and user guides View all 3M X55 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Troubleshooting Troubleshooting Related messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on. Message CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. Description The time the lamp timer has counted is approaching 2000 hours. Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer (36). When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by THE POWER WILL TURN OFF referring to the section "Lamp". After you have changed the AFTER ** hr. lamp, please be sure to reset the lamp timer (36). CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended. As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off. THE POWER WILL TURN OFF by referring to the section "Lamp". After changing the lamp, please be sure to reset the lamp timer (36). AFTER 0 hr. NO INPUT IS DETECTED ON *** Please immediately turn the power off, and change the lamp There is no input signal. Please confirm the signal input connection, and the status of the signal source. SYNC IS OUT OF RANGE ON *** fH *****kHz fV *****Hz The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs. CHECK THE AIR FLOW Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 35°C? • If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu. © 3M 2004 3M™ Digital Projector X45/SX55 The internal portion temperature is rising. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
42
Troubleshooting
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be
displayed. When any such message is displayed on the screen, please respond
as described below. If the same message is displayed after the treatment, or if a
message other than the following appears, please contact your dealer or service
company.
Although these messages will be automatically disappeared around several
minutes, it will be reappeared every time the power is turned on.
Message
Description
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
The time the lamp timer has counted is approaching
2000 hours.
Preparation of a new lamp, and an early lamp change is
recommended. After you have change the lamp, please be
sure to reset the lamp timer (
36
).
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
The time the lamp timer has counted is approaching
2000 hours, so a lamp change within
**
hours is
recommended.
When lamp usage reaches 2000 hours, the power will
automatically be turned off. Please change the lamp by
referring to the section “Lamp”. After you have changed the
lamp, please be sure to reset the lamp timer (
36
).
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
As the time the lamp timer has counted has reached
2000 hours, the power will soon be automatically
turned off.
Please immediately turn the power off, and change the lamp
by referring to the section “Lamp”. After changing the lamp,
please be sure to reset the lamp timer (
36
).
NO INPUT IS DETECTED
ON ***
There is no input signal.
Please confirm the signal input connection, and the status
of the signal source.
SYNC IS OUT OF RANGE
ON ***
fH
*****kHz
fV
*****Hz
The horizontal or vertical wavelength of the inputted
signal is outside of the response parameters of this unit.
Please confirm the specs for this unit or the signal source specs.
CHECK THE AIR FLOW
The internal portion temperature is rising.
Please turn the power OFF, and allow the unit to cool down at least 20 minutes.
After having confirmed the following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
•
If the same indication is displayed after the treatment, please set the
HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.
© 3M 200
4
3M™
Digital
Projector
X45/
S
X55