3M X76 Safety Guide - Page 8

Important Note - accessories

Get 3M X76 - Digital Projector XGA LCD PDF manuals and user guides
UPC - 051125632249
View all 3M X76 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

ENGLISH Important Note 1. Always open the lens shutter or remove lens cap when the projection lamp is on. 2. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ceiling mount or ceiling desktop mount) and continue to use the same lamp.  7RDYRLGUHGXFHGODPSOLIHGRQRWWRXFKSURMHFWLRQODPSZLWKEDUH¿QJHUV 4. To avoid reduced image quality, do not touch projection lens or other internal optical components. 5. Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other than those referred to in the "Operator's Guide". 6. For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass. Also, do not install an old or used lamp.  .HHSDLU¿OWHUFOHDQ5HIHUWRWKHFOHDQLQJLQVWUXFWLRQVFRQWDLQHGLQWKH³2SHUDWRU¶V Guide". 8. Keep all ventilation openings free of any obstructions. 9. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a bandwidth of 100 to 120 volts / 220 to 240 volts (50 to 60 Hz) ±10%, but could fail if power drops or surges of ±10 volts occur. In these highrisk areas, it is recommended to install a power stabilizer unit. 10. Do not block intake or exhaust air vents. This will cause the projector to over heat and shut down. 11. Do not place the projector in direct sunlight or near a hot object such as a heater. 12. To prevent damaging the projector, always hold the projector whenever using the elevator buttons to adjust the elevator feet. 13. Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. 14. Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. 15. Do not place the projector in the side/front/rear-up position, except care of the air ¿OWHU 16. Following information is only for EU-member states: The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law. 8 3M™ Digital Projector X76 Product Safety Guide © 3M 2008. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
3M™ Digital Projector X76 Product Safety Guide
© 3M 2008. All rights reserved.
8
ENGLISH
Important Note
1.
Always open the lens shutter or remove lens cap when the projection lamp is on.
2.
To avoid premature lamp failure, do not change the mounting position of the
projector (desktop ceiling mount or ceiling desktop mount) and continue to use the
same lamp.
4.
To avoid reduced image quality, do not touch projection lens or other internal
optical components.
5.
Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other
than those referred to in the “Operator's Guide”.
6.
For maximum lamp life, do not strike or drop, improperly handle, or scratch the
lamp glass. Also, do not install an old or used lamp.
Guide”.
8.
Keep all ventilation openings free of any obstructions.
9.
In some countries, the line voltage is NOT stable. This projector is designed to
operate safely within a bandwidth of 100 to 120 volts / 220 to 240 volts (50 to 60
Hz) ±10%, but could fail if power drops or surges of ±10 volts occur. In these high-
risk areas, it is recommended to install a power stabilizer unit.
10.
Do not block intake or exhaust air vents. This will cause the projector to over heat
and shut down.
11.
Do not place the projector in direct sunlight or near a hot object such as a heater.
12.
To prevent damaging the projector, always hold the projector whenever using the
elevator buttons to adjust the elevator feet.
13.
Use the accessory cable or a designated-type cable for the connection. Some
cables have to be used with core set. A too long cable may cause certain picture
degradation. Please consult with your dealer for details. For cables that have a
core only at one end, connect the core to the projector.
14.
Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
15.
Do not place the projector in the side/front/rear-up position, except care of the air
16.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.