AEG AXP34U338CW User Manual - Page 15

Celsius. Under Dry/Fan mode, you can

Page 15 highlights

ENGLISH 15 2. Press the "Fan speed" button to choose the desired fan speed. 3. The fan will run at the selected speed and the display will show the room temperature. Note: In this mode, auto speed cannot be selected. Auto mode Always have the exhaust hose attached in this mode. When you set the air conditioner in Auto mode, it will automatically select cooling, heating (inapplicable for cooling only models), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you. Under AUTO mode, you can not select the fan speed. 1. Press the "mode" button until the "Auto mode" indicator lights. After the "Auto mode" is selected the unit will run automatically according to the actual room air temperature. Timer mode The timer facilitates the user to delay the unit startup or shutdown. How to delay startup Plug in the unit, so the unit turns to standby. Press the "timer" button, then the Timer indicator will switch on and the number of hours on the screen will show "0.0". Tap or hold the UP arrow " " or the DOWN arrow " " to change delay start timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. Press the "timer" button again within 5 seconds, you will quit the timer setting directly. After 5 seconds, the timer function is enabled, the display will show the temperature back. The control will count down the time remaining until startup. The unit will start up in the mode as previously set. To cancel the setting, press the "timer" button again will show the remain time and press the button again to quit the function. You can also cancel the setting by pressing the "on/off" button. After cancel the setting, the timer indicator will switch off. How to delay shutdown You can delay shutdown when the unit is on. Press the "timer" button, then the Timer indicator will switch on and the number of hours on the screen will show "0.0". Tap or hold the UP arrow " " or the DOWN arrow " " to change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. Press the "timer" button again within 5 seconds, you will quit the timer setting directly. After 5 seconds, the timer function is enabled, the display will show the temperature back. The control will count down the time remaining until shuts down. To cancel the setting, press the "timer" button again will show the remaing time and press the button again to quit the function. You can also cancel the setting by pressing the "on/off" button. After cancel the setting, the timer indicator will switch off. Sleep mode Active this feature will give you a comfortable temperature and help save energy. Only when the unit is in Cool, Heat or auto mode, you can press the "sleep" button to make the unit run in Sleep mode. Note: Please refer to page 17 for the details about "Sleep" mode. Louver Swing Function Press the "swing" button to enable louver swing function, the louver on the top panel will swing up and down. Press this button again to disable the louver swing function. °F/°C function Press the " " and " " button the same time for more than 3 seconds to switch between degree Fahrenheit and degrees Celsius. Under Dry/Fan mode, you can not select °F/°C.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

15
ENGLISH
Auto mode
Timer mode
How to delay startup
Always have the exhaust hose attached
in this mode.
When you set the air conditioner
in Auto mode, it will automatically
select cooling, heating (inapplicable
for cooling only models), or fan
only operation depending on what
temperature you have selected and the
room temperature. The air conditioner
will control room temperature
automatically round the temperature
point set by you.
Under AUTO mode, you can not select
the fan speed.
1. Press the “mode” button until the “Auto
mode” indicator lights.
After the “Auto mode” is selected the unit
will run automatically according to the
actual room air temperature.
The timer facilitates the user to delay the
unit startup or shutdown.
Plug in the unit, so the unit turns to
standby.
Press the “timer” button, then the
Timer indicator will switch on and the
number of hours on the screen will
show “0.0”.
Tap or hold the UP arrow “
” or the
DOWN arrow “
” to change delay start
timer at 0.5 hour increments up to
10 hours, then at 1 hour increments
up to 24 hours. Press the “timer” button
again within 5 seconds, you will quit
the timer setting directly.
After 5 seconds, the timer function
is enabled, the display will show the
temperature back. The control will count
down the time remaining until startup.
The unit will start up in the mode as
previously set.
To cancel the setting, press the “timer”
button again will show the remain time
Note:
In this mode, auto speed cannot
be selected.
How to delay shutdown
You can delay shutdown when the unit
is on.
Press the “timer” button, then the Timer
indicator will switch on and the number
of hours on the screen will show “0.0”.
Tap or hold the UP arrow “
” or the
DOWN arrow “
” to change delay stop
timer at 0.5 hour increments up to 10
hours, then at 1 hour increments up to
24 hours. Press the “timer” button again
within 5 seconds, you will quit the timer
setting directly.
After 5 seconds, the timer function
is enabled, the display will show the
temperature back. The control will count
down the time remaining until shuts
down.
To cancel the setting, press the “timer”
button again will show the remaing time
and press the button again to quit the
function. You can also cancel the setting
by pressing the “on/off” button. After
cancel the setting, the timer indicator
will
switch off.
2.
Press the “Fan speed” button to
choose the desired fan speed.
3.
The fan will run at the selected speed
and the display will show the room
temperature.
and press the button again to quit the
function. You can also cancel the setting
by pressing the “on/off” button. After
cancel the setting, the timer indicator
will
switch off.
Sleep mode
Active this feature will give you a
comfortable temperature and help save
energy.
Only when the unit is in Cool, Heat or
auto mode, you can press the “sleep”
button to make the unit run in Sleep
mode.
Note: Please refer to page 17 for the
details about “Sleep” mode.
Press the “swing” button to enable louver
swing function, the louver on the top
panel will swing up and down.
Press this button again to disable the
louver swing function.
Louver Swing Function
°F/°C function
Press the “
” and “
” button the same
time for more than 3 seconds to switch
between degree Fahrenheit and degrees
Celsius. Under Dry/Fan mode, you can
not select °F/°C.