AEG T6DBG721N User Manual - Page 14

Hints And Tips

Get AEG T6DBG721N PDF manuals and user guides View all AEG T6DBG721N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

14 www.aeg.com Child lock option activation: 1. Turn the dryer on. 2. Select 1 of the available programs. 3. Touch and hold down 2 buttons at the same time. The symbol appears on the display. 4. To deactivate the child lock, touch the above buttons again until the symbol disappears. 8.8 Starting a program To start the program: Touch the Start/Pause button. The appliance starts and the LED above the button stops flashing and stays on. 8.9 Program change To change a program: 9. HINTS AND TIPS 9.1 Ecological hints • Spin the laundry well before drying. • Do not exceed the load sizes which are specified in the programs chapter. • Clean the filter after each drying cycle. • Do not use fabric softener to wash and then dry. In the tumble dryer laundry becomes soft automatically. • Use distilled water like that used for steam ironing. If it is necessary, clean 1. Push the On/Off button to turn the appliance off. 2. Push the On/Off button again to turn on the appliance. 3. Set a new program. 8.10 Program end Clean the filter and drain the water container after each drying cycle. (See chapter CARE AND CLEANING.) If the drying cycle is finished, the symbol appears on the display. If the Buzzer option is activated, the acoustic signal sounds intermittently for 1 minute. If you do not turn off the appliance, the anti-crease phase starts (not active with all programs). Flashing symbol signals the execution of the anticrease phase. Laundry can be removed during this phase. To remove the laundry: 1. Push the On/Off button for 2 seconds to turn the appliance off. 2. Open the appliance door. 3. Remove the laundry. 4. Close the appliance door. the distilled water before (e.g. with a coffee filter) to remove any particles. • Always keep the airflow slots at the bottom of the appliance clear. • Make sure there is good airflow where the appliance is to be installed. 9.2 Adjustment of default dryness level To change the default dryness level: 1. Turn the appliance on.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Child lock option activation:
1.
Turn the dryer on.
2.
Select 1 of the available programs.
3.
Touch and hold down 2 buttons at
the same time.
The symbol
appears on the display.
4.
To deactivate the child lock, touch
the above buttons again until the
symbol disappears.
8.8
Starting a program
To start the program:
Touch the
Start/Pause
button.
The appliance starts and the LED above
the button stops flashing and stays on.
8.9
Program change
To change a program:
1.
Push the On/Off button to turn the
appliance off.
2.
Push the On/Off button again to turn
on the appliance.
3.
Set a new program.
8.10
Program end
Clean the filter and drain the
water container after each
drying cycle. (See chapter
CARE AND CLEANING.)
If the drying cycle is finished, the symbol
appears on the display. If the Buzzer
option is activated, the acoustic signal
sounds intermittently for 1 minute.
If you do not turn off the
appliance, the anti-crease
phase starts (not active with
all programs). Flashing
symbol signals the execution
of the anticrease phase.
Laundry can be removed
during this phase.
To remove the laundry:
1.
Push the On/Off button for 2
seconds to turn the appliance off.
2.
Open the appliance door.
3.
Remove the laundry.
4.
Close the appliance door.
9.
HINTS AND TIPS
9.1
Ecological hints
•
Spin the laundry well before drying.
•
Do not exceed the load sizes which
are specified in the programs chapter.
•
Clean the filter after each drying
cycle.
•
Do not use fabric softener to wash
and then dry. In the tumble dryer
laundry becomes soft automatically.
•
Use distilled water like that used for
steam ironing. If it is necessary, clean
the distilled water before (e.g. with a
coffee filter) to remove any particles.
•
Always keep the airflow slots at the
bottom of the appliance clear.
•
Make sure there is good airflow where
the appliance is to be installed.
9.2
Adjustment of default
dryness level
To change the default dryness level:
1.
Turn the appliance on.
www.aeg.com
14