AIWA XH-A1000 Operating Instructions - Page 25

Play With Dolby Pro Logic

Get AIWA XH-A1000 PDF manuals and user guides View all AIWA XH-A1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2 Press MANUAL SELECT and hold it down for about 4 seconds until "L" flashes. PLAY WITH DOLBY PRO LOGIC A noise signal is sent to each channel in turn in the following sequence. AUX/ PHONO/ 5.1CH VIDEO 1/2/3 MANUAL SELECT f,g 3 Adjust the sound level of the center and the surround speakers. While "CEN", "S-R" or "S-L" is displayed, press f or g to adjust the volume of the center or surround speakers to match the level of the left and right speakers. To adjust the balance between the left and right front speakers, see page 11. 4 Press MANUAL SELECT again to stop the noise signal. NOTE • If the surround speakers or the center speaker level of the DOLBY PRO LOGIC is changed, that of the DSP SURROUND system (page 13) and the DOLBY DIGITAL SURROUND (page 25) is also changed. • While "S-R" or "S-L" is displayed, both surround speakers output the noise signal together. However, only the sound level of one surround speaker displayed as "S-R" or "S-L" can be adjusted. • When the sequencer outputs a noise signal, a clicking sound might be heard from the speakers due to the characteristics of the circuit. This is not malfunction. About the channels The left and right speakers create the stereo effect. The center speaker helps achieve precise sound positioning over a broad sound field. The surround speakers enhance the "depth" of the sound field. To change the delay time The surround speakers reproduce sounds a split second after the front speakers. The delay is initially set to 20 ms (milliseconds). To change this standard delay time, press MANUAL SELECT on the remote control repeatedly in NORMAL or PHANTOM mode until "TIME" is displayed. Then, press the f or g. Each time one of the buttons is pressed, the delay time changes as shown below. 15ms j l 20ms j l 30ms f,g 1 Press VIDEO 1/2/3 or AUX/PHONO/5.1CH. Then start playback of the video source. 2 Press DOLBY PRO LOGIC. NORMAL is selected, and the playback sound has the DOLBY PRO LOGIC effect. To cancel DOLBY PRO LOGIC mode Press DOLBY PRO LOGIC repeatedly until "OFF" is displayed. To change the sound levels during playback After adjusting the balance with the noise sequencer, the sound levels of the center or surround speakers can be adjusted during playback of laser discs or video software. 1 Press MANUAL SELECT on the remote control repeatedly to select "CEN" (center), "S-R" (surround right) or "S-L" (surround left). 2 While the "CEN", "S-R" or "S-L" is displayed, press f or g on the remote control to adjust the volume. 24 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
24
ENGLISH
PLAY WITH DOLBY PRO LOGIC
1
Press VIDEO 1/2/3 or AUX/PHONO/5.1CH. Then
start playback of the video source.
2
Press DOLBY PRO LOGIC.
NORMAL is selected, and the playback sound has the DOLBY
PRO LOGIC effect.
To cancel DOLBY PRO LOGIC mode
Press
DOLBY PRO LOGIC
repeatedly until “OFF” is displayed.
To change the sound levels during playback
After adjusting the balance with the noise sequencer, the sound
levels of the center or surround speakers can be adjusted during
playback of laser discs or video software.
1
Press
MANUAL SELECT
on the remote control repeatedly
to select
“CEN” (center), “S-R” (surround right) or “S-L”
(surround left).
2
While the “CEN”, “S-R” or “S-L” is displayed, press
f
or
g
on the remote control to adjust the volume.
AUX/
PHONO/
5.1CH
f
,
g
f
,
g
MANUAL
SELECT
VIDEO 1/2/3
2
Press MANUAL SELECT and hold it down for
about 4 seconds until “L” flashes.
A noise signal is sent to each channel in turn in the following
sequence.
3
Adjust the sound level of the center and the
surround speakers.
While “CEN”, “S-R” or “S-L” is displayed, press
f
or
g
to
adjust the volume of the center or surround speakers to match
the level of the left and right speakers.
To adjust the balance between the left and right front speakers,
see page 11.
4
Press MANUAL SELECT again to stop the noise
signal.
NOTE
• If the surround speakers or the center speaker level of the
DOLBY PRO LOGIC is changed, that of the DSP SURROUND
system (page 13) and the DOLBY DIGITAL SURROUND (page
25) is also changed.
•
While “S-R” or “S-L” is displayed, both surround speakers output
the noise signal together. However, only the sound level of one
surround speaker displayed as “S-R” or “S-L” can be adjusted.
• When the sequencer outputs a noise signal, a clicking sound
might be heard from the speakers due to the characteristics of
the circuit. This is not malfunction.
About the channels
The left and right speakers
create the stereo effect.
The center speaker
helps achieve precise sound positioning
over a broad sound field.
The surround speakers
enhance the “depth” of the sound field.
To change the delay time
The surround speakers reproduce sounds a split second after
the front speakers. The delay is initially set to 20 ms (milliseconds).
To change this standard delay time, press
MANUAL SELECT
on the remote control repeatedly in NORMAL or PHANTOM mode
until “TIME” is displayed. Then, press the
f
or
g
. Each time
one of the buttons is pressed, the delay time changes as shown
below.
l
j
l
j
15ms
20ms
30ms