ASRock N3150TM-ITX User Manual - Page 20

Signal

Get ASRock N3150TM-ITX PDF manuals and user guides View all ASRock N3150TM-ITX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

N3150TM-ITX Front Panel Audio Header OUT_RET (9-pin HD_AUDIO1) MIC_RED (see p.5, No. 25) PRESENCE# GND OUT2_L his header is for J_SENSE connecting audio devices OUT2_R MIC2_R to the front audio panel. MIC2_L 1 1. High Deinition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system. 2. If you use an AC'97 audio panel, please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for the HD audio panel only. You don't need to connect them for the AC'97 audio panel. E. To activate the front mic, go to the "FrontMic" Tab in the Realtek Control panel and adjust "Recording Volume". Analog Surround Audio Header (17-pin HD_AUDIO2) (see p.5, No. 28) Signal Signal PIN PIN Name Name 18 SENSE 17 KEY 16 LFE 15 A_GND 14 A_GND 13 Center 12 Surr_Rear_R 11 A_GND 10 A_GND 9 Surr_Rear_L 8 Surr_Side_R 7 A_GND 2 1 6 A_GND 5 Surr_Side_L 4 Front_R 3 A_GND 2 A_GND 1 Front_L 3W Audio AMP Output Wafer Header (4-pin SPEAKER1) (see p.5, No. 27) 1 Front_LFront_L+ Front_R+ Front_R- Please connect the chassis speaker to this header. English 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
15
English
N3150TM-ITX
Front Panel Audio ³eader
(9-pin ³D_AUDIO1)
(see p.5, No. 25)
His header is for
connecting audio devices
to the front audio panel.
Analog Surround
Audio ³eader
(17-pin ³D_AUDIO2)
(see p.5, No. 28)
3W Audio AMP Output
Wafer ³eader
(4-pin SPEAKER1)
(see p.5, No. 27)
Please connect the chassis
speaker to this header.
1
2
PIN
Signal
Name
PIN
Signal
Name
18
SENSE
17
KEY
16
LFE
15
A_GND
14
A_GND
13
Center
12
Surr_Rear_R
11
A_GND
10
A_GND
9
Surr_Rear_L
8
Surr_Side_R
7
A_GND
6
A_GND
5
Surr_Side_L
4
Front_R
3
A_GND
2
A_GND
1
Front_L
Front_L+
Front_R-
Front_R+
Front_L-
1
1.
´igh DeInition Audio supports Jack Sensing, but the panel wire on the chassis must sup-
port ´DA to function correctly. Please follow the instructions in our manual and chassis
manual to install your system.
2. ±f you use an AC’97 audio panel, please install it to the front panel audio header by the
steps below:
A. Connect Mic_±N (M±C) to M±C2_L.
B. Connect Audio_R (R±N) to OU³2_R and Audio_L (L±N) to OU³2_L.
C. Connect Ground (GND) to Ground (GND).
D. M±C_RE³ and OU³_RE³ are for the ´D audio panel only. You don’t need to connect
them for the AC’97 audio panel.
E. ³o activate the front mic, go to the “FrontMic” ³ab in the Realtek Control panel and
adjust “Recording Volume”.
J_SENSE
OUT2_L
1
MIC_RED
OUT_RET
OUT2_R
MIC2_R
MIC2_L
GND
PRESENCE#