ASRock N68-GS4 FX User Manual - Page 19

Onboard Headers and Connectors

Get ASRock N68-GS4 FX PDF manuals and user guides View all ASRock N68-GS4 FX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! • Floppy Connector (33-pin FLOPPY1) (see p.11 No. 18) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (39-pin IDE1, see p.11 No. 6) PIN1 IDE1 connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATA2 Connectors (SATAII_1 (PORT 0.0): see p.11, No. 9) (SATAII_2 (PORT 0.1): see p.11, No. 5) (SATAII_3 (PORT 1.0): see p.11, No. 8) (SATAII_4 (PORT 1.1): see p.11, No. 7) SATAII_3 SATAII_1 (PORT 1.0) (PORT 0.0) SATAII_4 SATAII_2 (PORT 1.1) (PORT 0.1) These four Serial ATA2 (SATA2) connectors support SATA2 or SATA hard disk for internal storage devices. The current SATA2 interface allows up to 3.0 Gb/s data transfer rate. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
19
19
19
19
19
FLOPPY
1
Pin
1
the red-striped side to Pin1
2.6
Onboard Headers and Connectors
2.6
Onboard Headers and Connectors
2.6
Onboard Headers and Connectors
2.6
Onboard Headers and Connectors
2.6
Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.11 No. 18)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector
(39-pin IDE1, see p.11 No. 6)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATA2 Connectors
These four Serial ATA2 (SATA2)
(SATAII_1 (PORT 0.0):
connectors support SATA2
see p.11, No. 9)
or SATA hard disk for internal
(SATAII_2 (PORT 0.1):
storage devices. The current
see p.11, No. 5)
SATA2 interface allows up to
(SATAII_3 (PORT 1.0):
3.0 Gb/s data transfer rate.
see p.11, No. 8)
(SATAII_4 (PORT 1.1):
see p.11, No. 7)
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
IDE
1
PIN1
80-conductor ATA 66/100/133 cable
SATAII_3
SATAII_1
(PORT 1.0)
(PORT 0.0)
SATAII_4
SATAII_2
(PORT 1.1)
(PORT 0.1)