ASRock N68PV-GS Quick Installation Guide - Page 16

English, 6 Onboard Headers and Connectors

Get ASRock N68PV-GS PDF manuals and user guides View all ASRock N68PV-GS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent dam- age of the motherboard! • Floppy Connector (33-pin FLOPPY1) (see p.2 No. 19) the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.2 No. 7) connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1 (PORT 0): see p.2, No. 6) (SATAII_2 (PORT 1): see p.2, No. 5) (SATAII_3 (PORT 2): see p.2, No. 9) (SATAII_4 (PORT 3): see p.2, No. 8) SATAII_1 (PORT 0) SATAII_2 (PORT 1) SATAII_3 (PORT 2) SATAII_4 (PORT 3) These four Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. Serial ATA (SATA) Please connect the black end of Power Cable SATA power cable to the power (Optional) 16 connect to the SATA HDD power connector connect to the power supply connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. ASRock N68PV-GS Motherboard English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
16
16
16
16
16
ASRock
N68PV-GS
Motherboard
English
English
English
English
English
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100/133 cable
the red-striped side to Pin1
connect
to the
power supply
connect
to the SATA
HDD power connector
2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper
caps over the headers and connectors will cause permanent dam-
age of the motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.2 No. 19)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.2 No. 7)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These four Serial ATAII (SATAII)
(SATAII_1 (PORT 0):
connectors support SATAII
see p.2, No. 6)
or SATA hard disk for internal
(SATAII_2 (PORT 1):
storage devices. The current
see p.2, No. 5)
SATAII interface allows up to
(SATAII_3 (PORT 2):
3.0 Gb/s data transfer rate.
see p.2, No. 9)
(SATAII_4 (PORT 3):
see p.2, No. 8)
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on the motherboard.
Serial ATA (SATA)
Please connect the black end of
Power Cable
SATA power cable to the power
(Optional)
connector on each drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
SATAII_2 (PORT 1)
SATAII_4 (PORT 3)
SATAII_3 (PORT 2)
SATAII_1 (PORT 0)