ASRock NF6-GLAN Quick Installation Guide - Page 14

English, 5 Onboard Headers and Connectors

Get ASRock NF6-GLAN PDF manuals and user guides View all ASRock NF6-GLAN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

2.5 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent dam- age of the motherboard! • Floppy Connector (33-pin FLOPPY1) (see p.2 No. 22) the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.2 No. 8) connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1 (PORT 1.0): see p.2, No. 12) (SATAII_2 (PORT 1.1): see p.2, No. 16) (SATAII_3 (PORT 2.0): see p.2, No. 11) (SATAII_4 (PORT 2.1): see p.2, No. 10) These four Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. SATAII_2 (PORT 1.1) SATAII_4 (PORT 2.1) SATAII_1 (PORT 1.0) SATAII_3 (PORT 2.0) English Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. 14 ASRock NF6-GLAN Motherboard

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
14
14
14
14
14
ASRock
NF6-GLAN
Motherboard
English
English
English
English
English
the red-striped side to
Pin1
2.5 Onboard Headers and Connectors
2.5 Onboard Headers and Connectors
2.5 Onboard Headers and Connectors
2.5 Onboard Headers and Connectors
2.5 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper
caps over the headers and connectors will cause permanent dam-
age of the motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.2 No. 22)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.2 No. 8)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These four Serial ATAII (SATAII)
(SATAII_1 (PORT 1.0): see p.2, No. 12)
connectors support SATAII
(SATAII_2 (PORT 1.1): see p.2, No. 16)
or SATA hard disk for internal
(SATAII_3 (PORT 2.0): see p.2, No. 11)
storage devices. The current
(SATAII_4 (PORT 2.1): see p.2, No. 10)
SATAII interface allows up to
3.0 Gb/s data transfer rate.
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on the motherboard.
80-conductor ATA 66/100/133 cable
SATAII_1 (PORT 1.0)
SATAII_3 (PORT 2.0)
SATAII_2 (PORT 1.1)
SATAII_4 (PORT 2.1)