Acer AT310 F1 User Manual - Page 112

Initial troubleshooting checklist - driver

Get Acer AT310 F1 PDF manuals and user guides View all Acer AT310 F1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

94 5 System troubleshooting Initial troubleshooting checklist Use the checklist below to eliminate possible causes for the problem you are encountering. • AC power is available at the wall outlet? • Is the power supply module properly installed? • Is the system power cord properly plugged into the power supply module socket? and connected to a NEMA 5-15R outlet for 100-120 V or a NEMA 6-15R outlet for 200-240 V? • Are all peripheral cables correctly connected and secured? • Did you press the system power button to turn the server on (power on indicator should be lit green)? • Are all device drivers properly installed? • Are hard disk drive(s) properly formatted and configured? • Are the BIOS configuration settings in the BIOS Setup Utility correct? • Is the operating system properly loaded? Refer to the operating system documentation. • Are all hardware components compliant with the tested components lists? • Are all internal cables correctly connected and secured? • Is the processor properly seated in its mainboard socket? • Are all standoffs in the proper location and not touching any components, causing a potential short? • Are all add-in expansion cards fully seated in their mainboard slots? • Are all system jumpers correctly set? • Are all switch settings on add-in boards and peripheral devices correct? To check these settings, refer to the manufacturer's documentation that comes with them. If applicable, ensure that there are no conflicts (e.g., two add-in boards sharing the same interrupt).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
5 System troubleshooting
94
Initial troubleshooting checklist
Use the checklist below to eliminate possible causes for the problem
you are encountering.
•
AC power is available at the wall outlet?
•
Is the power supply module properly installed?
•
Is the system power cord properly plugged into the power supply
module socket? and connected to a NEMA 5-15R outlet for
100-120 V or a NEMA 6-15R outlet for 200-240 V?
•
Are all peripheral cables correctly connected and secured?
•
Did you press the system power button to turn the server on
(power on indicator should be lit green)?
•
Are all device drivers properly installed?
•
Are hard disk drive(s) properly formatted and configured?
•
Are the BIOS configuration settings in the BIOS Setup Utility
correct?
•
Is the operating system properly loaded?
Refer to the operating system documentation.
•
Are all hardware components compliant with the tested
components lists?
•
Are all internal cables correctly connected and secured?
•
Is the processor properly seated in its mainboard socket?
•
Are all standoffs in the proper location and not touching any
components, causing a potential short?
•
Are all add-in expansion cards fully seated in their mainboard
slots?
•
Are all system jumpers correctly set?
•
Are all switch settings on add-in boards and peripheral devices
correct?
To check these settings, refer to the manufacturer’s
documentation that comes with them. If applicable, ensure that
there are no conflicts (e.g., two add-in boards sharing the same
interrupt).