Acer Altos R300 Acer Altos R300 User's Guide - Page 56

cable 3 connected to the floppy drive and hard disk. - driver

Get Acer Altos R300 PDF manuals and user guides View all Acer Altos R300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

42 3 Upgrading your system To remove the hard disk drive under the floppy disk drive: a Disconnect the diskette drive (1), hard disk (2) and power cable (3) connected to the floppy drive and hard disk. Note: To remove the floppy drive cable, use your fingers or a flat screw driver to gently lift the cable retainer on the connector (a) then lift the cable up as shown inset on the figure below. Attach the cable retainer to the connector and push it in to connect the floppy disk drive cable (b,c). b Remove the screw that holds the diskette drive and hard disk assembly to the housing (4). c Slide (5) then lift up the assembly from the system housing (6).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
3 Upgrading your system
42
To remove the hard disk drive under the floppy disk drive:
a
Disconnect the diskette drive (1), hard disk (2) and power
cable (3) connected to the floppy drive and hard disk.
Note:
To remove the floppy drive cable, use your fingers or a flat
screw driver to gently lift the cable retainer on the connector (a)
then lift the cable up as shown inset on the figure below.
Attach the cable retainer to the connector and push it in to
connect the floppy disk drive cable (b,c).
b
Remove the screw that holds the diskette drive and hard disk
assembly to the housing (4).
c
Slide (5) then lift up the assembly from the system housing (6).