Acer H5382BD User Manual - Page 42

V OSD is On simultaneously, Internal 5V OSD will be set as

Get Acer H5382BD PDF manuals and user guides View all Acer H5382BD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

32 English Internal 5V VGA OUT (Standby) HDMI CEC Reset Security Default is "Off". Switch On to supply 5V power for both of power on mode and standby mode. 1. Before doing OSD Reset: projector detects and shows that inner HDMI 2/MHL port after being plugged by non-MHL dongle (ex: Chromecast). 2. After doing OSD Reset: If inner HDMI dongle existd and Internal 5V (OSD) is On simultaneously, Internal 5V (OSD) will be set as On and DC 5V Out (OSD) will be set as Off automatically after doing OSD Reset. (Since inner HDMI dongle isn't given power by projector causing inner dongle's signal is lost and cannot be detected by projector) Default is "Off". Choose "On" to enable VGA OUT connection. Default is "Off". Select "On" to enable HDMI CEC function. Press the "ENTER" button and choose "Yes" to return the parameters on all menus to the factory default settings. Security This projector provides a useful security function for the administrator to manage usage of the projector . Press "ENTER" to change the "Security" setting. If the security function is enabled, your must enter the "Administrator Password" first before changing the security settings. • Select "On" to enable the security function. The user has to enter a password to operate the projector. Please refer to the "User Password" section for details. • If "Off" is selected, then the user can turn on the projector without password. Timeout(Min.) Once "Security" is activated to "On", the administrator can set timeout function. • Press or to select the timeout interval. • The range is from 10 minute to 990 minutes. • When the time is up, the projector will prompt the user to enter the password again. • The factory default setting of "Timeout(Min.)" is "Off". • Once the security function is enabled, the projector will request user to enter password when switch on the projector . Both "User Password" and "Administrator Password" can be accepted for this dialogue. User Password • Press "ENTER" to setup or change the "User Password". • Press number keys to set your password on the remote control and press "ENTER" to confirm. • Press to delete character. • Enter the password when you see "Confirm Password" displayed. • The password should be between 4 and 8 characters long. • If you select "Request password only when plugging the power cord in.", the projector will prompt the user to enter the password every time the power cord is plugged. • If you select "Always request password while projector turns on.", the user has to enter the password every time when the projector is turned on.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
32
English
Internal 5V
Default is "Off". Switch On to supply 5V power for both of power
on mode and standby mode.
<Note>
1. Before doing OSD Reset: projector detects and shows that inner
HDMI 2/MHL port after being plugged by non-MHL dongle (ex:
Chromecast).
2. After doing OSD Reset: If inner HDMI dongle existd and Internal
5V (OSD) is On simultaneously, Internal 5V (OSD) will be set as On
and DC 5V Out (OSD) will be set as Off automatically after doing
OSD Reset. (Since inner HDMI dongle isn't given power by projector
causing inner dongle's signal is lost and cannot be detected by
projector)
VGA OUT (Standby)
Default is "Off". Choose "On" to enable VGA OUT connection.
HDMI CEC
Default is "Off". Select “On” to enable HDMI CEC function.
Reset
Press the "ENTER" button and choose "Yes" to return the
parameters on all menus to the factory default settings.
Security
Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press "ENTER" to change the "Security" setting. If the security
function is enabled, your must enter the "Administrator Password"
first before changing the security settings.
•
Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector
without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•
Press
or
to select the timeout interval.
•
The range is from 10 minute to 990 minutes.
•
When the time is up, the projector will prompt the user to
enter the password again.
•
The factory default setting of "Timeout(Min.)" is "Off".
•
Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
User Password
•
Press "ENTER" to setup or change the "User Password".
•
Press number keys to set your password on the remote control
and press "ENTER" to confirm.
•
Press
to delete character.
•
Enter the password when you see "Confirm Password"
displayed.
•
The password should be between 4 and 8 characters long.
•
If you select "Request password only when plugging the
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
•
If you select "Always request password while projector turns
on.", the user has to enter the password every time when the
projector is turned on.