Adaptec 1045 User Guide - Page 48

VERIFY, Command Syntax, Command Switches, Example, VERSION, SATA/SAS controller.

Get Adaptec 1045 PDF manuals and user guides View all Adaptec 1045 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Appendix 10: Using the Adaptec Flash Utility for DOS ● 48 Adaptec Flash Utility V1.0 (c)Adaptec Inc. 1999-2008. All Rights Reserved. Updating Controller 0 (ASC-1045/1405) Reading flash image file (Build 0018) AFU is about to update BIOS on controller(s) Adaptec ASC-1045 ***PLEASE DO NOT REBOOT THE SYSTEM DURING THE UPDATE*** This might take a few minutes. Writing ASC-1045/1405 Flash Image to controller 0...OK. Please restart your computer for the new BIOS changes to take effect. VERIFY The VERIFY command compares the contents of the flash components on a SATA/SAS controller to the corresponding image in a UFI file, and determines whether the SAS controller's flash components are up-to-date. Command Syntax The command syntax for the VERIFY command is as follows: AFU VERIFY [/C] [/D ] Command Switches For details on the /C and /D switches, see SAVE on page 46. Example The below example shows a typical system response after a VERIFY command is performed: A:\> AFU VERIFY /C 0 Adaptec Flash Utility V1.0 (c)Adaptec Inc. 1999-2008. All Rights Reserved. Reading flash image file (Build 0018) Controller #0: ASC-1045/1405 File: Checksum: 642C [VALID] (Build 1406) Verified Successfully VERSION The VERSION command displays the version information about the flash components on a SATA/SAS controller. Command Syntax The command syntax for the VERSION command is as follows: AFU VERSION [/C] Command Switches For details on the /C switch, see SAVE on page 46. Example The below example displays the version information about all supported SATA/SAS controllers:

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Appendix 10: Using the Adaptec Flash Utility for DOS
●
48
Adaptec Flash Utility V1.0
(c)Adaptec Inc. 1999–2008. All Rights Reserved.
Updating Controller 0 (ASC-1045/1405)
Reading flash image file (Build 0018)
AFU is about to update BIOS on controller(s) Adaptec ASC-1045
***PLEASE DO NOT REBOOT THE SYSTEM DURING THE UPDATE***
This might take a few minutes.
Writing ASC-1045/1405 Flash Image to controller 0...OK.
Please restart your computer for the new BIOS changes to take effect.
VERIFY
The
VERIFY
command compares the contents of the flash components on a SATA/SAS
controller to the corresponding image in a UFI file, and determines whether the
SAS
controller’s flash components are up-to-date.
Command Syntax
The command syntax for the
VERIFY
command is as follows:
AFU VERIFY [/C<
Controller ID
>] [/D <
UFI File Path
>]
Command Switches
For details on the /C and /D switches, see
SAVE
on page 46
.
Example
The below example shows a typical system response after a
VERIFY
command is performed:
A:\> AFU VERIFY /C 0
Adaptec Flash Utility V1.0
(c)Adaptec Inc. 1999–2008. All Rights Reserved.
Reading flash image file (Build 0018)
Controller #0: ASC-1045/1405
File: Checksum: 642C [VALID] (Build 1406)
Verified Successfully
VERSION
The
VERSION
command displays the version information about the flash components on a
SATA/SAS controller.
Command Syntax
The command syntax for the
VERSION
command is as follows:
AFU VERSION [/C<
Controller ID
>]
Command Switches
For details on the /C switch, see
SAVE
on page 46
.
Example
The below example displays the version information about all supported SATA/SAS
controllers: