Alesis NanoVerb 2 Quick Start Guide - Page 3

Quickstart Guide English - footswitch

Get Alesis NanoVerb 2 PDF manuals and user guides View all Alesis NanoVerb 2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

QUICKSTART GUIDE (ENGLISH) 1. Make sure all items listed in the Box Contents are included. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Place the product in an appropriate location for operation. 4. Ensure high quality, shielded audio cables are used away from sources of electromagnetic interference. BOX CONTENTS ƒ NANOVERB 2 ƒ Power Adapter ƒ Quickstart Guide ƒ Safety Instructions & Warranty Information Booklet FRONT PANEL 254 3 67 1 1. POWER LED - Light will illuminate once the unit is powered on 2. INPUT - Controls both the Left (Mono) and Right channel analog input signal level 3. SIGNAL LED - LED will light up if the signal level is too high which may cause distortion. If this occurs, turn down the Input control knob and/or reduce the output level from your instrument source 4. OUTPUT - Adjusts the analog output signal level 5. MIX - Adjusts the balance between the incoming "dry" signal and the effect-processed signal. When this knob is turned to the far left, no processed signal will be heard. When the knob is turned to the middle position, an equal mix of the dry and processed signal will be heard. When the knob is turned to the far right, only the processed signal will be heard 6. EFFECTS SELECTOR - Select one of the 16 factory presets with this knob 7. PROGRAM - This will switch between different variations of the effect REAR PANEL 8 11 10 10 9 9 8. POWER CONNECTOR - Plug the included AC adapter here (9v AC 500mA) 9. INPUT - Connect the ¼" unbalanced inputs to your source, such as Aux Sends on a mixer. For mono sources, just connect to the Left (Mono) input on the NANOVERB 2 10. OUTPUT - Connect the ¼" unbalanced outputs to an Aux Return on a mixer, powered speakers, or amplifer input 11. BYPASS - Attach a momentary (non-latching) footswitch to this 1/4" phone jack. When the footswitch is pressed, the NANOVERB 2 will bypass the effects and only the dry signal will pass through the unit. If the footswitch is pressed again, effects will continue to output 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
3
QUICKSTART GUIDE (ENGLISH)
1.
Make sure all items listed in the Box Contents are included.
2.
READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE
PRODUCT.
3.
Place the product in an appropriate location for operation.
4.
Ensure high quality, shielded audio cables are used away from
sources of electromagnetic interference.
FRONT PANEL
5
1
2
3
4
6
7
1.
POWER LED
–
Light will illuminate once the unit is powered on
2.
INPUT
–
Controls both the Left (Mono) and Right channel analog input signal level
3.
SIGNAL LED
–
LED will light up if the signal level is too high which may cause distortion. If this occurs, turn
down the Input control knob and/or reduce the output level from your instrument source
4.
OUTPUT
–
Adjusts the analog output signal level
5.
MIX
–
Adjusts the balance between the incoming "dry" signal and the effect-processed signal. When this knob is
turned to the far left, no processed signal will be heard. When the knob is turned to the middle position, an equal
mix of the dry and processed signal will be heard. When the knob is turned to the far right, only the processed
signal will be heard
6.
EFFECTS SELECTOR
– Select one of the 16 factory presets with this knob
7.
PROGRAM
– This will switch between different variations of the effect
REAR PANEL
8
9
9
10
10
11
8.
POWER CONNECTOR
– Plug the included AC adapter here (9v AC 500mA)
9.
INPUT
– Connect the ¼” unbalanced inputs to your source, such as Aux Sends on a mixer. For mono sources,
just connect to the Left (Mono) input on the NANOVERB 2
10. OUTPUT
– Connect the ¼” unbalanced outputs to an Aux Return on a mixer, powered speakers, or amplifer
input
11. BYPASS
– Attach a momentary (non-latching) footswitch to this 1/4" phone jack. When the footswitch is pressed,
the NANOVERB 2 will bypass the effects and only the dry signal will pass through the unit. If the footswitch is
pressed again, effects will continue to output
BOX CONTENTS
NANOVERB 2
Power Adapter
Quickstart Guide
Safety Instructions &
Warranty Information
Booklet