Alpine CDA-117 Owner's Manual (english) - Page 28

SAT Radio Receiver (optional) Rotary encoder/ENTER/ BAND SOURCE/ /ESC  4 Press  or  to select the desired channel. Holding down  or  will change channels continuously. 1 While in XM or SIRIUS Radio mode, enter the Channel number you want to call up with the numeric keypad on the remote control. 2 Press Enter on the remote control within 5 seconds to receive the Channel. Note • When using the optional remote control (RUE-4190, etc.), an SAT Radio Channel can be directly called up with the numeric keypad of the remote control. Checking the SAT Radio ID Number    FUNC. VIEW Preset buttons (1 through 6) SAT Receiver: XM or SIRIUS Receiver* When an optional XM or SIRIUS Receiver Box is connected via the Ai-NET bus, the following operations may be performed. However, the XM Receiver and SIRIUS Receiver cannot be connected at the same time. * Verify the features of the connected SIRIUS Receiver Box. Not all SIRIUS Receivers have identical functions and some may not be performed on this unit. For details about functions, refer to the SIRIUS Receiver's Owner's Manual. Receiving Channels with the SAT Radio Receiver (optional) About SAT Radio Satellite Radio*1-*2 is the next generation of audio entertainment, with over 100 digital audio channels. For a small monthly fee, subscribers can hear crystal-clear music, sports, news and talk, coast-to-coast via satellite. For more information, visit XM's website at www.xmradio.com, or SIRIUS' website at www.sirius.com. *1 XM and its corresponding logos are trademarks of XM Satellite Radio Inc. *2 SIRIUS and its corresponding logos are trademarks of SIRIUS Satellite Radio Inc. To receive SAT Radio, the separately sold XM Direct™ or SIRIUS Satellite Radio Tuner and an appropriate Ai-NET Interface Adapter will be required. For details, consult you nearest Alpine dealer. Note • The SAT Receiver controls on this unit are operative only when a SAT Receiver is connected. 1 Press SOURCE to activate the SAT Radio mode. 2 Press BAND to select one of the three SAT Radio Preset Bands. Each press changes the band: XM mode: XM1  XM2  XM3  XM1 SIRIUS mode: SIRIUS1  SIRIUS2  SIRIUS3  SIRIUS1 3 Press  or  to select desired category. A unique SAT Radio ID number is required to subscribe to SAT Radio programming. Each third party XM or SIRIUS radio comes with this number. This number is an 8 character (for XM Radio) or 12 character (for SIRIUS Radio) alphanumeric number. It is printed on a label found on the SAT Receiver. It can also be displayed on the screen of this unit in the following way. XM mode: 1 While receiving a SAT Radio band, press  or  to select channel "0" for XM. The unit displays "RADIO ID" and ID number simultaneously. While displaying "RADIO ID" as shown above, Demonstration become nonfunctional (refer to "Demonstration" on page 23). 2 To cancel the ID number display, select the channel other than "0". SIRIUS mode: 1 While receiving a SAT Radio band, press  or  to select channel "255" or "0" for SIRIUS. 2 Press VIEW until the ID No. appears in the display. The SIRIUS ID is displayed when the Song Name display mode is toggled. For details, refer to "Changing the Display" on page 29. 3 To cancel the ID number display, set the channel to other than "255" and "0". Note • You can check the ID number printed on a label on your third party, SAT Radio Receiver package. Storing Channel Presets 1 Press BAND to select the desired band you want to store. 2 After tuning in the desired channel, press and hold, for at least 2 seconds, any one of the preset buttons (1 through 6) into which you wish to store the channel. The selected channel is stored. 3 Repeat the procedure to store up to 5 other channels onto the same band. Notes • To use this procedure for other bands, simply select the band desired and repeat the procedure. 26-EN