Alpine CDE-163BT Owners Manual - Page 10

Initial System Start-Up, Adjusting Volume, Setting the Dimmer Control, CDE-163BT Only, Setting Time - remote

Get Alpine CDE-163BT PDF manuals and user guides View all Alpine CDE-163BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Attaching Notes • Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. • Attach the front panel carefully, holding the sides of the front panel to avoid pushing buttons by mistake. Initial System Start-Up Be sure to press the RESET switch when using the unit for the first time, after changing the car battery, etc. RESET switch Adjusting Volume Turn the Rotary encoder until the desired sound is obtained. Setting Time 1 Press and hold YSETUP for at least 2 seconds to activate the SETUP selection mode. 2 Turn the Rotary encoder to select GENERAL, and then press ENTER. 3 Turn the Rotary encoder to select the CLOCK ADJ mode, and then press ENTER. The time indication will blink. 4 Turn the Rotary encoder to adjust the hours while the time indication is blinking. 5 When the hour has been adjusted, press ENTER. 6 Turn the Rotary encoder to adjust the minutes while the time indication is blinking. 7 Press and hold YSETUP for at least 2 seconds to return to normal mode. Notes • To synchronize the clock to another clock/watch or radio time announcement, press and hold ENTER for at least 2 seconds after setting the "hour". Minutes will reset to "00". If the display shows over "30" minutes when you do this, the time will advance one hour. • Pressing t will return to the previous mode. • If no operation is performed for 60 seconds, the unit will return to normal mode automatically. Controllable with Remote Control This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor. Remote control sensor Setting the Dimmer Control (CDE-163BT Only) Press and hold DIM. for at least 2 seconds repeatedly to select the DIMMER mode. DIMMERAUTO  DIMMER ON  DIMMER OFF  DIMMERAUTO DIMMERAUTO mode: Decrease the illumination brightness of the unit's buttons with the head lights of the vehicle ON. This mode decreases the unit's backlighting in sync with headlight usage. DIMMER ON mode: Keep the illumination brightness of the backlighting dimmed. DIMMER OFF mode: Keep the illumination brightness of the backlighting bright. Note • The setting items are the same as DISPLAY setting in SETUP mode. For details, refer to "Dimmer Control" on page 27. Connectable to Remote Control Interface Box With an optional Alpine Steering Wheel Remote Control Interface Box (not included), this unit is controllable from the vehicles steering wheel controls. For details, contact your Alpine dealer. 10-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
10
-EN
Notes
•
Before attaching the front panel, make sure that there is no dirt or dust
on the connector terminals and no foreign object between the front
panel and the main unit.
•
Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the
RESET
switch when using the unit for the first time,
after changing the car battery, etc.
Adjusting Volume
Turn the
Rotary encoder
until the desired sound is
obtained.
Setting the Dimmer Control
(CDE-163BT Only)
Press and hold
DIM.
for at least 2 seconds repeatedly to
select the DIMMER mode.
DIMMERAUTO
DIMMER ON
DIMMER OFF
DIMMERAUTO
DIMMERAUTO mode:
Decrease the illumination brightness of the unit’s buttons with the
head lights of the vehicle ON. This mode decreases the unit’s
backlighting in sync with headlight usage.
DIMMER ON mode:
Keep the illumination brightness of the backlighting dimmed.
DIMMER OFF mode:
Keep the illumination brightness of the backlighting bright.
Note
•
The setting items are the same as DISPLAY setting in SETUP mode.
For details, refer to “Dimmer Control” on page 27.
Setting Time
1
Press and hold
Y
SETUP
for at least 2 seconds to
activate the SETUP selection mode.
2
Turn the
Rotary encoder
to select GENERAL, and then
press

ENTER
.
3
Turn the
Rotary encoder
to select the CLOCK ADJ mode,
and then press

ENTER
.
The time indication will blink.
4
Turn the
Rotary encoder
to adjust the hours while the
time indication is blinking.
5
When the hour has been adjusted, press

ENTER
.
6
Turn the
Rotary encoder
to adjust the minutes while the
time indication is blinking.
7
Press and hold
Y
SETUP
for at least 2 seconds to return
to normal mode.
Notes
•
To synchronize the clock to another clock/watch or radio time
announcement, press and hold

ENTER
for at least 2 seconds after
setting the “hour”. Minutes will reset to “00”. If the display shows over
“30” minutes when you do this, the time will advance one hour.
•
Pressing
t
will return to the previous mode.
•
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Attaching
RESET switch
Controllable with Remote Control
This unit can be controlled with an optional Alpine remote control.
For details, consult your Alpine dealer.
Point the optional remote control transmitter at the remote control
sensor.
Connectable to Remote Control Interface Box
With an optional Alpine Steering Wheel Remote Control Interface
Box (not included), this unit is controllable from the vehicles
steering wheel controls. For details, contact your Alpine dealer.
Remote control sensor