Alpine V180A Operation Manual - Page 5

Connections

Get Alpine V180A - VPE - VCR PDF manuals and user guides View all Alpine V180A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Connections English Connecting the Power Cord Ë Connecting directly to the vehicle's power supply Disconnection Connection with a Monitor This unit can be connected to any Video Monitor, sold separately. Connect the VIDEO/AUDIO OUT terminal to the mobile monitor's Video Input terminal. Mobile Color TV System Ë Remote Control Input Wire When connecting to the CVA-1005 or TME-M750A monitors, it is possible to use the supplied remote control input wire to pass the signal from the monitor to the VPE-V180A. Dashboard, etc. Velcro (Hard surface side) Black Ground Wire. TUNER UNIT External Remote Eye Fuse Red Yellow Switched 12V where power goes on when the ignition key is turned to the ACC position. Constant 12V source (unswitched) Second TV, etc. AV Cable (Supplied) Remote control input wire Peel off the backing paper, then affix the velcro. Mount on the dashboard, etc. Note: Use one method only to pass remote control signal. Replacing the Fuse This unit is equipped with a 5A (Ampere) fuse connected to the DC power cable. If the fuse blows as soon as it has been replaced, please consult with the retailer where you purchased the unit. Furthermore, do not use a fuse with a higher rating than 5A under any circumstances. Fuse VIDEO Cable (Not supplied) OUT IN RIGHT AUDIO LEFT VIDEO Connecting other devices Ë External Remote Eye When the unit is mounted in the trunk or luggage compartment, etc., in a location where it is difficult to operate using the remote control, use the accessory External Remote Eye. Affix this device to the dashboard or other location which is appropriate for operation using the Remote Control. Notes • Use this unit with the vehicle's engine running. If it is used with the engine stopped, the vehicle's battery will run down and it may become impossible to start the engine. • Be sure that the unit is turned Off before turning the vehicle's ignition key to the Off position. If it is running when the ignition key is turned off, it could cause the tape or unit to be damaged. • If power is removed from the unit while it is operating (during playback, fast forward, rewind, etc.), it could result in damage. Please be sure to eject the tape from the unit before disconnecting power. • To prevent damage to your tapes, always be sure to press the Stop button before turning the vehicle's ignition key OFF. E-4 VPE-V180A_English 4 4/25/00, 2:02 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
English
E-4
Connections
Connecting the Power Cord
Connecting directly to the vehicle’s power
supply
Black
Red
Yellow
Fuse
Replacing the Fuse
This unit is equipped with a
5A
(Ampere) fuse con-
nected to the DC power cable.
If the fuse blows as soon as it has been replaced,
please consult with the retailer where you pur-
chased the unit. Furthermore, do not use a fuse
with a higher rating than
5A
under any circum-
stances.
Connection with a Monitor
This unit can be connected to any Video Monitor,
sold separately.
Connect the VIDEO/AUDIO OUT terminal to the
mobile monitor’s Video Input terminal.
OUT
RIGHT
LEFT
VIDEO
AUDIO
IN
Connecting other devices
External Remote Eye
When the unit is mounted in the trunk or luggage
compartment, etc., in a location where it is diffi-
cult to operate using the remote control, use the
accessory External Remote Eye.
Affix this device to the dashboard or other loca-
tion which is appropriate for operation using the
Remote Control.
Constant 12V source (unswitched)
Switched 12V where power goes
on when the ignition key is turned
to the ACC position.
Ground Wire.
Remote Control Input Wire
When connecting to the CVA-1005 or TME-M750A
monitors, it is possible to use the supplied remote
control input wire to pass the signal from the moni-
tor to the VPE-V180A.
Notes
• Use this unit with the vehicle’s engine running. If
it is used with the engine stopped, the vehicle’s
battery will run down and it may become impos-
sible to start the engine.
• Be sure that the unit is turned Off before turning
the vehicle’s ignition key to the Off position. If it is
running when the ignition key is turned off, it could
cause the tape or unit to be damaged.
• If power is removed from the unit while it is oper-
ating (during playback, fast forward, rewind, etc.),
it could result in damage. Please be sure to eject
the tape from the unit before disconnecting power.
• To prevent damage to your tapes, always be sure
to press the Stop button before turning the
vehicle’s ignition key OFF.
AV Cable (Supplied)
VIDEO Cable
(Not supplied)
Fuse
Peel off the backing
paper, then affix the
velcro.
Mount on the dash-
board, etc.
TUNER
UNIT
Mobile Color TV System
Second TV, etc.
Remote control input wire
Note:
Use one method only to pass remote control signal.
Velcro (Hard surface side)
Dashboard, etc.
External Remote Eye
Disconnection
VPE-V180A_English
4/25/00, 2:02 PM
4