Alpine iLX-007 Owner's Manual (english) - Page 27

Installation

Get Alpine iLX-007 PDF manuals and user guides View all Alpine iLX-007 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installation Note on installation • Install at an angle between horizontal and 30°. Note that installing at an angle outside of this range will result in a loss of performance and possible damage. Cable clamp (Sold separately) Microphone 0 - 30R° ear of the Unit • Do not block the unit's heat sink, which would prevent air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Rear of the Unit Installing the Unit 1 Remove the Face Plate from the unit. 2 Mount the original mounting bracket to the unit using the supplied screws. Original Mounting Bracket Screws (M5 x 8) (Included) Heat sink Ground Lead*1 Face Plate (Included)*2 Uninstalling the original car stereo 1 Uninstall the car stereo with its mounting bracket. 2 Remove the cables and the mounting bracket attached to the car stereo. (The mounting bracket will be used in "Installing the unit".) Mounting the Microphone. For safe use, make sure of the following: • Location is stable and firm. • Driver's view and operations are not obstructed. • Microphone is located where the driver's voice can be easily picked up (for example, on the sun visor). When you speak into the microphone, you should not have to change your driving posture. This may cause a distraction, taking your attention away from safely driving your vehicle. Carefully consider direction and distance while mounting the microphone. Confirm that the driver's voice can be easily picked up at the selected location. Chassis 3 Connect all other leads of the unit according to details described in the "Connections" section (page 29). 4 Mounting the unit in a car. *1 To securely connect the ground lead, use an already installed screw on a metal part of the vehicle (marked ( )) or a clean, bare metal spot on the vehicle's chassis. *2 Use the removed Face Plate if needed. Fix the Cables etc. Fix the cables carefully. Do not damage them by tucking them into movable parts, such as a seat rail, or by locating them against sharp or pointed edges. 27-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
27
-EN
Installation
1
Uninstall the car stereo with its mounting bracket.
2
Remove the cables and the mounting bracket
attached to the car stereo.
(The mounting bracket will be used in “Installing the unit”.)
For safe use, make sure of the following:
•
Location is stable and firm.
•
Driver’s view and operations are not obstructed.
•
Microphone is located where the driver’s voice can be easily
picked up (for example, on the sun visor).
When you speak into the microphone, you should not have to
change your driving posture. This may cause a distraction,
taking your attention away from safely driving your vehicle.
Carefully consider direction and distance while mounting the
microphone. Confirm that the driver’s voice can be easily picked
up at the selected location.
1
Remove the Face Plate from the unit.
2
Mount the original mounting bracket to the unit
using the supplied screws.
3
Connect all other leads of the unit according to
details described in the “Connections” section
(page 29).
4
Mounting the unit in a car.
*
1
To securely connect the ground lead, use an already installed screw
on a metal part of the vehicle (marked (
)) or a clean, bare metal
spot on the vehicle’s chassis.
*
2
Use the removed Face Plate if needed.
Fix the cables carefully. Do not damage them by tucking them
into movable parts, such as a seat rail, or by locating them
against sharp or pointed edges.
Uninstalling the original car stereo
Mounting the Microphone.
Note on installation
•
Install at an angle between horizontal and 30°. Note that
installing at an angle outside of this range will result in a
loss of performance and possible damage.
0 - 30°
•
Do not block the unit’s heat sink, which would prevent air
circulation. If blocked, heat will accumulate inside the
unit and may cause a fire.
Heat sink
Rear of the Unit
Installing the Unit
Fix the Cables etc.
Microphone
Cable clamp
(Sold separately)
Original Mounting Bracket
Screws (M5 x 8)
(Included)
Face Plate (Included)
*
2
Ground Lead
*
1
Chassis