American Standard 3208.016.222 Installation Instructions

American Standard 3208.016.222 - Antiquity/Repertoire Elongated Toilet Bowl Manual

Get American Standard 3208.016.222 - Antiquity/Repertoire Elongated Toilet Bowl PDF manuals and user guides
UPC - 033056485125
View all American Standard 3208.016.222 manuals
Add to My Manuals
Save this manual to your list of manuals

American Standard 3208.016.222 manual content summary:

  • American Standard 3208.016.222 | Installation Instructions - Page 1
    INSTRUCTIONS For Two-Piece Toilets with Aquameter™ Fill Valve REPERTOIRE 2266/2483 HERITAGE 2176 ANTIQUITY 2264/2464 WILLIAMSBURG 2264.702 Thank you for selecting American Standard putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed! 2 ROUGHING-
  • American Standard 3208.016.222 | Installation Instructions - Page 2
    through mounting holes. b. Loosely install mounting clip (for Heritage only), retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! c. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until
  • American Standard 3208.016.222 | Installation Instructions - Page 3
    on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish. ! WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall
  • American Standard 3208.016.222 | Installation Instructions - Page 4
    TROUBLESHOOTING GUIDE PROBLEM Does not flush Poor or sluggish flush Toilet leaks Toilet instructions to increase water control flow rate. AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY If inspection of this American-Standard plumbing affect such statutory rights. For service under this warranty, it
  • 1
  • 2
  • 3
  • 4
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely.
Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line.
NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90˚,
and slide into place 6" (152 mm) apart and
parallel to wall.
S
A
V
E
F
O
R
F
U
T
U
R
E
U
S
E
3
2
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must
be as listed below:
CLOSET FLANGE
CLOSET BOLTS
730489-100 Rev. B
12"
(305mm)
FINISHED WALL
FINISHED
FLOOR
Saniwares
CAUTION:
PRODUCT IS FRAGILE.
TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE:
Pictures may not exactly define contour of china and components.
!
REPERTOIRE 2266/2483
HERITAGE 2176
ANTIQUITY 2264/2464
WILLIAMSBURG 2264.702
Thank you
for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes
INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with Aquameter™ Fill Valve
SUPPLY AS
REQUIRED
12
(305mm)
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2006