Asko D5636XXLHS/PH Installation instructions EN - Page 10
Moving The Machine Into Place
View all Asko D5636XXLHS/PH manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
MOVING THE MACHINE INTO PLACE Rear foot Front feet 1˝ (24 mm) 1˝ (24 mm) ADJUSTING MACHINES WITH THREE OR FOUR FEET 1. Position the machine in front of the cabinet opening. 2. Push the plastic feet into place on all steel feet (included in document bag). (Only certain models.) 3. Start by measuring the height from the floor to the bottom edge of the counter top. Measure the height from the floor to the top edge of the dishwasher. 4. Loosen the lock nuts on the dishwasher's steel feet using a 5/8˝ (16 mm) open-ended wrench. Screw the lock nuts down as close to the floor as possible. 5. Make the height adjustment while the dishwasher is in front of the opening. Adjust all feet by turning them clockwise to raise or counterclockwise to lower the dishwasher. 6. Check that the height of the machine corresponds to the height from the floor to the bottom edge of the counter top. 7. Tighten the lock nuts (lock nut) on the rear feet (foot). 8. Pull out the drain hose to ensure there are no sharp bends. 9. Start to feed water and drain lines and electric cord (if necessary) into the access hole(s) in the cabinet. 10. Gently slide the unit into the dishwasher opening. As you do this, feed the drain line and inlet hose into the access hole(s) in the side of the cabinet. 11. If installing in a metal cabinet, the hole(s) for the drain hose and connection pipe must be fitted with edge protectors/rubber grommets. 12. Place the spirit level on the dishwasher door to check that the machine is level and adjust if necessary. The door must be fully closed! 13. Make any final adjustments to the front feet. (The machine may have an inclination of 3/16˝ (5 mm) maximum without affecting its performance.) 14. When the front feet are properly adjusted, tighten the lock nuts to the base pan. ADJUSTING MACHINES WITH FRONT ADJUSTABLE REAR FOOT 1. Position the machine in front of the cabinet opening. 2. Push the plastic feet into place on all steel feet (included in document bag). (Only certain models.) 3. Start by measuring the height from the floor to the bottom edge of the counter top. Measure the height from the floor to the top edge of the dishwasher. 4. Loosen the lock nuts on the dishwasher's front steel feet using a 5/8˝ (16 mm) open-ended wrench. Screw the lock nuts down as close to the floor as possible. 5. Lean the dishwasher forwards a little and roughly adjust the rear foot by turning the adjustment screw at the front clockwise to raise and counterclockwise to lower the dishwasher (see illustration above). Use a flat-bladed screwdriver or a 1/4˝ nut driver. 6. Adjust the front feet by turning them clockwise to raise or counterclockwise to lower the dishwasher. 7. Check that the height of the machine corresponds to the height from the floor to the bottom edge of the counter top. 8. Pull out the drain hose to ensure there are no sharp bends. 9. Start to feed water and drain lines and electric cord (if necessary) into the access hole(s) in the cabinet. 10. Gently slide the unit into the dishwasher opening. As you do this, feed the drain line and inlet hose into the access hole(s) in the side of the cabinet. 11. If installing in a metal cabinet, the hole(s) for the drain hose and connection pipe must be fitted with edge protectors/rubber grommets. 12. Place the spirit level on the dishwasher door to check that the machine is level and adjust if necessary. The door must be fully closed! 13. Make any final adjustments to the feet. (The machine may have an inclination of 3/16˝ (5 mm) maximum without affecting its performance.) 14. When the feet are properly adjusted, tighten the lock nuts on the front feet to the base pan. 10 CUSTOMER CARE CENTER 1-800-898-1879 • WWW.ASKONA.COM