Asus A620M-AYW WIFI PRIME PROART TUF GAMING AMD AM5 Series BIOS Manual Simplif - Page 80
AIO Pump Q-Fan Control, AIO Pump Profile, AIO Pump Q-Fan Source, AIO Pump Step Up, AIO Pump Step
View all Asus A620M-AYW WIFI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 80 highlights
AIO Pump Q-Fan Control AIO Pump [Auto Detect [DC Mode] 在 DC Q-Fan Control 來使用 3-pin [PWM Mode] 在 PWM Q-Fan Control 來使用 4-pin AIO Pump Profile Manual 75°C 100 Standard] [Silent] [Turbo] [Full Speed] [Manual] AIO Fan Profile 設為 [Standard]、[Silent]、[Turbo] 或 [Manual AIO Pump Q-Fan Source CPU] [MotherBoard] [VRM] [Chipset] [T_Sensor] [Multiple Sources] AIO Pump Step Up 0 Level 0] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] AIO Pump Step Down 0 Level 0] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] AIO Pump Speed Low Limit Ignore Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] AIO Pump Profile 設為 [Manual AIO Pump Point4 Temperature P4 P3-P4 P4 P4 Point4 80 PRIME / ProArt / TUF GAMING AMD 600 系列 BIOS
80
PRIME / ProArt / TUF GAMING AMD 600 系列 BIOS 用戶手冊
AIO Pump Q-Fan Control
本項目用來設置 AIO Pump 運作模式。
[Auto Detect]
檢測安裝的風扇/水泵類型並自動切換控制模式。
[DC Mode]
在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水泵。
[PWM Mode]
在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/水泵。
AIO Pump Profile
本項目用來設置風扇/水泵適當的性能。選擇 [Manual] 時,當處理器溫度超
過 75°C 時,建議將風扇/水泵的占空比設為 100%。請留意當風扇/水泵占
空比不足導致過熱,會造成處理器性能限制。設置值有:[Standard] [Silent]
[Turbo] [Full Speed] [Manual]
以下項目只有在 AIO Fan Profile 設為 [Standard]、[Silent]、[Turbo] 或 [Manual]
時才會出現。
AIO Pump Q-Fan Source
指派的風扇/水泵會依選擇的溫度來源運作。設置值有:[CPU] [MotherBoard]
[VRM] [Chipset] [T_Sensor] [Multiple Sources]
AIO Pump Step Up
本項目用來設置處理器風扇的加速。等級 0 是速度的瞬時變化。等級越高,
速度變化越慢,也可能導致噪音更小,但這也會導致散熱速度更慢。設置值
有:[Level 0] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5]
AIO Pump Step Down
本項目用來設置處理器風扇的減速。等級 0 是速度的瞬時變化。等級越高,
速度變化越慢,可能導致噪音持續期間較長。設置值有:[Level 0] [Level 1]
[Level 2] [Level 3] [Level 4] [Level 5]
AIO Pump Speed Low Limit
本項目用來設置風扇/水泵的最低速度警告值。當達到這個最低速度時,會出
現警告信息。若設定為 [Ignore],將不會再出現警告信息。設置值有:[Ignore]
[200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
以下項目只有在 AIO Pump Profile 設為 [Manual] 時才會出現。
AIO Pump Point4 Temperature
當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大
於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調整 Point4 的溫
度。