Asus A7N8X-VM 400 A7N8X-VM/400 User's Manual - Page 23

Connectors

Get Asus A7N8X-VM 400 PDF manuals and user guides View all Asus A7N8X-VM 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

1.11 Connectors This section describes and illustrates the connectors on the motherboard. 1. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) This connector supports the provided UltraATA 133/100/66/33 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraATA 133/100/66/33 slave device (hard disk drive) and the black connector to the UltraATA 133/100/66/33 master device. It is recommended that you connect non-UltraATA 133/100/66/33 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup. If you have more than two UltraATA 133/100/66/33 devices, purchase another UltraATA 133/100/66/33 cable. You may configure two hard disks to be both master devices with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector. Pin 20 on each IDE connector is removed to match the covered hole on the UltraATA cable connector. This prevents incorrect orientation when you connect the cables. For UltraATA 133/100/66/33IDE devices, use an 80-conductor IDE cable. A7N8X-VM 400 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_IDE PRI_IDE A7N8X-VM 400 IDE Connectors PIN 1 ASUS A7N8X-VM 400 Motherboard 1-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
ASUS A7N8X-VM 400 Motherboard
1-13
1.11
Connectors
This section describes and illustrates the connectors on the motherboard.
1.
IDE connectors (40-1 pin PRI_IDE, SEC_IDE)
This connector supports the provided UltraATA 133/100/66/33 IDE hard disk
ribbon cable. Connect the cable’s blue connector to the primary
(recommended) or secondary IDE connector, then connect the gray connector
to the UltraATA 133/100/66/33 slave device (hard disk drive) and the black
connector to the UltraATA 133/100/66/33 master device. It is recommended
that you connect non-UltraATA 133/100/66/33 devices to the secondary IDE
connector. If you install two hard disks, you must configure the second drive as
a slave device by setting its jumper accordingly. Refer to the hard disk
documentation for the jumper settings. BIOS supports specific device bootup.
If you have more than two UltraATA 133/100/66/33 devices, purchase another
UltraATA 133/100/66/33 cable. You may configure two hard disks to be both
master devices with two ribbon cables – one for the primary IDE connector and
another for the secondary IDE connector.
Pin 20 on each IDE connector is removed to match the covered hole
on the UltraATA cable connector. This prevents incorrect orientation
when you connect the cables.
For UltraATA 133/100/66/33IDE devices, use an 80-conductor IDE
cable.
A7N8X-VM 400
A7N8X-VM 400 IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PIN 1
PRI_IDE