Asus AAM6010EV-T4 User Manual - Page 33

Tools, Remote Log, User Management, System Commands, Save All, Update Gateway, Note: Do not remove - m firmware

Get Asus AAM6010EV-T4 PDF manuals and user guides View all Asus AAM6010EV-T4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

AAM6010EV-T4 User Manual Table 1 defines the different severity levels. To forward logging information, you need to click on Tools (at the top of the page) and select Remote Log. Table 1 (Severity Level) 4.7.3 User Management You can change your CPE's username and password by going to the Home screen, under the tools menu, click User Management. From here you can change the login name and password. You can also change the idle timeout; you will need to log back onto the CPE once the timeout expires. If you forget your password, you can press and hold the reset to factory defaults button for 10 seconds (or more). The CPE will reset to its factory default configuration and all custom configurations will be lost. The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of the page) and select System Commands. At the system commands page, click on Save All. 4.7.4 Update Gateway You can remotely upgrade the CPE's firmware by going to the Home screen, under the tools title, click Update Gateway. This will bring up the screen shown in Figure 21. TI will provide two different images; one image is the kernel (operating system) and the other image is the file system. To upgrade the firmware, click browse, find the firmware file to download. Make sure this is the correct file. Click on upgrade firmware (as shown in Figure 21). Once the upgrade is complete the CPE will reboot. You will need to log back onto the CPE after the firmware upgrade is complete. The firmware upgrade should take less that 5 minutes to complete. If it takes longer than 5 minutes, something has gone wrong. Note: Do not remove power from the CPE during the firmware upgrade procedure. 33 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
AAM6010EV-T4 User Manual
33
33
Table 1 defines the different severity levels.
To forward logging information, you need to click on
Tools
(at the top of the page) and select
Remote Log
.
Table 1 (Severity Level)
4.7.3
User Management
You can change your CPE’s username and password by going to the Home screen, under the tools menu,
click User Management.
From here you can change the login name and password.
You can also change
the idle timeout; you will need to log back onto the CPE once the timeout expires.
If you forget your password, you can press and hold the reset to factory defaults button for 10 seconds (or
more).
The CPE will reset to its factory default configuration and all custom configurations will be lost.
The apply button will temporarily save this connection. To make the change permanent you need to click
on
Tools
(at the top of the page) and select
System Commands
.
At the system commands page, click on
Save All
.
4.7.4
Update Gateway
You can remotely upgrade the CPE’s firmware by going to the Home screen, under the tools title, click
Update Gateway.
This will bring up the screen shown in Figure 21.
TI will provide two different images;
one image is the kernel (operating system) and the other image is the file system.
To upgrade the firmware, click browse, find the firmware file to download.
Make sure this is the correct
file.
Click on upgrade firmware (as shown in Figure 21).
Once the upgrade is complete the CPE will
reboot.
You will need to log back onto the CPE after the firmware upgrade is complete.
The firmware upgrade should take less that 5 minutes to complete.
If it takes longer than 5 minutes,
something has gone wrong.
Note: Do not remove power from the CPE during the firmware upgrade procedure.