Asus K7V K7V User Manual - Page 27

Installing the Processor

Get Asus K7V PDF manuals and user guides View all Asus K7V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3. HARDWARE SETUP 1. Place the motherboard on the anti-static foam that was shipped with the motherboard. Do not place the motherboard on a hard surface while installing the URM as the black fastener sleeves must protrude through the bottom of the motherboard. 2. Locate the Slot A connector on the motherboard. 3. Position the retention mechanism on either side of the Slot A connector. 4. Making sure that the top retainer pins are not pushed in, press down on the retention brackets until the black fastener sleeves fit snugly against the board. WARNING! Installing the URM while the retainer pins are pushed in will not only cause the URM to be installed improperly but will also damage the URM. 5. Push the four retainer pins completely down into the black fastener sleeves until the head of each pin is securely seated. 3. H/W SETUP CPU 3.6.4 Installing the Processor NOTE: The following steps assume that you have already attached the heatsink and installed the URM into your motherboard. 1. Make sure that the processor substrate key is aligned with the Slot A connector key. Substrate Key Connector Key ASUS K7V User's Manual 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
ASUS K7V User’s Manual
27
3. HARDWARE SETUP
CPU
3. H/W SETUP
1.
Place the motherboard on the anti-static foam that was shipped with the mother-
board. Do not place the motherboard on a hard surface while installing the URM
as the black fastener sleeves must protrude through the bottom of the mother-
board.
2.
Locate the Slot A connector on the motherboard.
3.
Position the retention mechanism on either side of the Slot A connector.
4.
Making sure that the top retainer pins are not pushed in, press down on the
retention brackets until the black fastener sleeves fit snugly against the board.
5.
Push the four retainer pins completely down into the black fastener sleeves until
the head of each pin is securely seated.
WARNING!
Installing the URM while the retainer pins are pushed in will not
only cause the URM to be installed improperly but will also damage the URM.
3.6.4
Installing the Processor
NOTE:
The following steps assume that you have already attached the heatsink and
installed the URM into your motherboard.
1.
Make sure that the processor substrate key is aligned with the Slot A connector key.
Substrate Key
Connector Key