Asus M2R32-MVP Motherboard Installation Guide - Page 52

with a jumper cap. Remove the jumper caps only when you intend

Get Asus M2R32-MVP - Motherboard - ATX PDF manuals and user guides
UPC - 610839141074
View all Asus M2R32-MVP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

8 . Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pins labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. ® +5VSB_MB Chassis Signal GND M2R32-MVP CHASSIS (Default) M2R32-MVP Chassis intrusion connector 9 . Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF module cable to this connector, then install the module to a slot opening at the back of the system chassis. The S/PDIF module is purchased separately. M2R32-MVP ® SPDIF_OUT GND SPDIFOUT +5V M2R32-MVP COM port connector 2-30 Chapter 2: Hardware information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
2-30
2-30
2-30
2-30
2-30
Chapter 2: Hardware information
Chapter 2: Hardware information
Chapter 2: Hardware information
Chapter 2: Hardware information
Chapter 2: Hardware information
8.
8.
8.
8.
8.
Chassis intrusion connector (4-1 pin CHASSIS)
Chassis intrusion connector (4-1 pin CHASSIS)
Chassis intrusion connector (4-1 pin CHASSIS)
Chassis intrusion connector (4-1 pin CHASSIS)
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
M2R32-MVP
M2R32-MVP Chassis intrusion connector
CHASSIS
+5VSB_MB
Chassis Signal
GND
(Default)
9.
9.
9.
9.
9.
Digital audio connector (4-1 pin SPDIF_OUT)
Digital audio connector (4-1 pin SPDIF_OUT)
Digital audio connector (4-1 pin SPDIF_OUT)
Digital audio connector (4-1 pin SPDIF_OUT)
Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface
(S/PDIF) port(s). Connect the S/PDIF module cable to this connector,
then install the module to a slot opening at the back of the system
chassis.
The S/PDIF module is purchased separately.
M2R32-MVP
M2R32-MVP COM port connector
+5V
SPDIFOUT
GND
SPDIF_OUT