Asus P4V800D-X Motherboard DIY Troubleshooting Guide - Page 28

Internal connectors

Get Asus P4V800D-X PDF manuals and user guides View all Asus P4V800D-X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1.10.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. P4V800D-X FLOPPY ® PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P4V800D-X Floppy disk drive connector 2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) This connector is for an Ultra DMA 133 signal cable. The Ultra DMA 133 signal cable has three connectors: a blue connector for the IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. P4V800D-X ® PIN 1 P4V800D-X IDE connectors PRI_IDE SEC_IDE NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PIN 1 1-18 Chapter 1: Product Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
1-18
Chapter 1: Product Introduction
P4V800D-X
P4V800D-X IDE connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PRI_IDE
PIN 1
PIN 1
P4V800D-X
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
P4V800D-X Floppy disk drive connector
PIN 1
FLOPPY
2.
IDE connectors (40-1 pin PRI_IDE, SEC_IDE)
This connector is for an Ultra DMA 133 signal cable. The Ultra
DMA 133 signal cable has three connectors: a blue connector for the
IDE connector on the motherboard, a black connector for an Ultra
DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and
a gray connector for an Ultra DMA 133/100/66 IDE master device
(hard disk drive). If you install two hard disk drives, you must configure
the second drive as a slave device by setting its jumper accordingly.
Refer to the hard disk documentation for the jumper settings.
1.10.2 Internal connectors
1.
Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable. Insert
one end of the cable to this connector, then connect the other end to the
signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection when
using a FDD cable with a covered Pin 5.
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.