Asus P5BV-C User Guide - Page 70

RAID 0+1, or RAID 5 configurations using the Intel® Matrix Storage Manager - raid driver

Get Asus P5BV-C - Motherboard - ATX PDF manuals and user guides
UPC - 610839157372
View all Asus P5BV-C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Configure SATA as [IDE] Sets the configuration for the Serial ATA connectors supported by the Southbridge chip. Configuration options: [IDE] [RAID] [AHCI] If you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices, set this item to [IDE]. Set this item to [RAID], if you want to create a RAID 0, RAID 1, RAID 0+1, or RAID 5 configurations using the Intel® Matrix Storage Manager or if you want to create a RAID 0, RAID 1, RAID 0+1 configurations using the LSI Logic Embedded SATA RAID Setup Utility. Set the item Configure SATA as to [RAID] if you want to use or configure the SATA connectors under SuSE Linux Enterprise Server 9.0 SP1 operating system environment. Due to the OS limitation, you must set a SATA RAID to use any SATA device (at least two SATA devices are needed for the RAID configuration). Refer to Chapter 5 and Chapter 6 for details on how to set a SATA RAID. Set Configure SATA As to [RAID], if you want to create a RAID 0, RAID 1, RAID 0+1, or RAID 5 configurations using the Intel® Matrix Storage Manager or if you want to create a RAID 0, RAID 1, RAID 0+1 configurations using the LSI Logic Embedded SATA RAID Setup Utility. OnBoard Serial-ATA BOOTROM [Disabled] Allows you to enable or disable the Onboard Serial-ATA BOOTROM. Configuration options: [Disabled] [Enabled] The AHCI allows the onboard storage driver to enable advanced Serial ATA features that enhance storage performance on random workloads by allowing the drive to internally optimize the order of commands. If you want the Serial ATA hard disk drives to use the Advanced Host Controller Interface (AHCI), set this item to [AHCI]. For details on AHCI, go to: www.intel.com/support/chipsets/imst/sb/CS-012304.htm www.intel.com/support/chipsets/imst/sb/CS-012305.htm The SATA controller is set to Native mode when this item is set to [RAID] or [AHCI]. ALPE and ASP [Disabled] Allows you to enable or disable the Aggressive Link Power Management and Aggressive Slumber/Partial Enabled. Configuration options: [Disabled] [Enabled] Stagger Spinup Support [Disabled] Allows you to enable or disable the Stagger Spinup support function. Configuration options: [Disabled] [Enabled] 4-12 Chapter 4: BIOS setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
4-12
Chapter 4: BIOS setup
Configure SATA as [IDE]
Sets the configuration for the Serial ATA connectors supported by the
Southbridge chip. Configuration options: [IDE] [RAID] [AHCI]
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, set this item to [IDE].
Set this item to [RAID], if you want to create a RAID 0, RAID 1, RAID 0+1, or
RAID 5 configurations using the Intel
®
Matrix Storage Manager or if you want
to create a RAID 0, RAID 1, RAID 0+1 configurations using the LSI Logic
Embedded SATA RAID Setup Utility.
Set Configure SATA As to [RAID], if you want to create a RAID 0, RAID 1,
RAID 0+1, or RAID 5 configurations using the Intel® Matrix Storage Manager
or if you want to create a RAID 0, RAID 1, RAID 0+1 configurations using the
LSI Logic Embedded SATA RAID Setup Utility.
OnBoard Serial-ATA BOOTROM [Disabled]
Allows you to enable or disable the Onboard Serial-ATA BOOTROM.
Configuration options: [Disabled] [Enabled]
The AHCI allows the onboard storage driver to enable advanced Serial ATA
features that enhance storage performance on random workloads by allowing
the drive to internally optimize the order of commands.
If you want the Serial ATA hard disk drives to use the Advanced Host
Controller Interface (AHCI), set this item to [AHCI]. For details on AHCI, go
to:
www.intel.com/support/chipsets/imst/sb/CS-012304.htm
www.intel.com/support/chipsets/imst/sb/CS-012305.htm
The SATA controller is set to Native mode when this item is set to [RAID] or
[AHCI].
ALPE and ASP [Disabled]
Allows you to enable or disable the Aggressive Link Power Management
and Aggressive Slumber/Partial Enabled. Configuration options: [Disabled]
[Enabled]
Stagger Spinup Support [Disabled]
Allows you to enable or disable the Stagger Spinup support function.
Configuration options: [Disabled] [Enabled]
Set the item
Configure SATA as
to [RAID] if you want to use or configure
the SATA connectors under SuSE Linux Enterprise Server 9.0 SP1 operating
system environment. Due to the OS limitation, you must set a SATA RAID to
use any SATA device (at least two SATA devices are needed for the RAID
configuration). Refer to Chapter 5 and Chapter 6 for details on how to set a
SATA RAID.