Asus P8H61-I LX RM User Guide - Page 52

SATA Configuration, System Agent Configuration

Get Asus P8H61-I LX RM PDF manuals and user guides View all Asus P8H61-I LX RM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2.5.3 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. SATA Mode Selection [IDE] Allows you to set the SATA configuration. [Disabled] Disables the SATA function. [IDE] Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. [AHCI] Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. • Due to H61 chipset limitation, AHCI Mode only works on Windows® Vista / 7. Please use [IDE Mode] on Windows® XP. • [IDE] is the default SATA type. Under Windows® XP, there is no need to change the SATA type. • To configure the SATA type in BIOS, click Advanced Mode > Advanced tab > SATA Configuration > OnChip SATA Type. S.M.A.R.T. Status Check [Enabled] S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. This item appears only when you set the previous item to [IDE] or [AHCI]. Configuration options: [Enabled] [Disabled] Hot Plug [Disabled] This item only appears when you set the SATA Mode Selection item to [AHCI] and allows you to enable or disable the hot-plug support for each SATA port. Configuration options: [Enabled] [Disabled] 2.5.4 System Agent Configuration Memory Remap Feature [Enabled] [Enabled] Allow you to enable remapping the memory above 4GB. [Disabled] Disables this function. Graphics Configuration Primary Display [Auto] Allows you to decide which graphics controller to use as the primary boot device. Configuration options: [Auto] [iGPU] [PCIE] iGPU Memory [Auto] Allows you to select the amount of system memory allocated to DVMT 5.0 used by the iGPU. Configuration options: [Auto] [32M] [64M] [96M] [128M] ~ [416M] [448M] [480M] [512M] 2-18 ASUS P8H61-I LX R2.0

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
2-18
ASUS P8H61-I LX R2.0
2.5.3
SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show
Not Present
if no SATA device is installed to the corresponding SATA
port.
SATA Mode Selection [IDE]
Allows you to set the SATA configuration.
[Disabled]
Disables the SATA function.
[IDE]
Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
[AHCI]
Set to [AHCI Mode] when you want the SATA hard disk drives to use the
AHCI (Advanced Host Controller Interface). The AHCI allows the onboard
storage driver to enable advanced Serial ATA features that increases
storage performance on random workloads by allowing the drive to
internally optimize the order of commands.
•
Due to H61 chipset limitation, AHCI Mode only works on Windows
®
Vista / 7. Please use
[IDE Mode] on Windows
®
XP.
•
[IDE] is the default SATA type. Under Windows
®
XP, there is no need to change the
SATA type.
•
To configure the SATA type in BIOS, click
Advanced Mode
>
Advanced
tab >
SATA
Configuration
>
OnChip SATA Type
.
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST. This item appears only when you set the previous item to [IDE]
or [AHCI]. Configuration options: [Enabled] [Disabled]
Hot Plug [Disabled]
This item only appears when you set the SATA Mode Selection item to [AHCI] and allows you
to enable or disable the hot-plug support for each SATA port. Configuration options: [Enabled]
[Disabled]
2.5.4
System Agent Configuration
Memory Remap Feature [Enabled]
[Enabled]
Allow you to enable remapping the memory above 4GB.
[Disabled]
Disables this function.
Graphics Configuration
Primary Display [Auto]
Allows you to decide which graphics controller to use as the primary boot device.
Configuration options: [Auto] [iGPU] [PCIE]
iGPU Memory [Auto]
Allows you to select the amount of system memory allocated to DVMT 5.0 used by the
iGPU. Configuration options: [Auto] [32M] [64M] [96M] [128M] ~ [416M] [448M] [480M]
[512M]