Home » Asus Manuals » Motherboards » Asus P8Q67-M DO BR » Manual Viewer

Asus P8Q67-M DO BR User Manual - Page 23

P8Q67-M DO/USB3/TPM Chassis intrusion connector

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

3. CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND P8Q67-M DO/USB3/TPM CHA_FAN GND +12V Rotation P8Q67-M DO/USB3/TPM Fan connectors Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power. 4. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pin labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. CHASSIS +5VSB_MB Chassis Signal GND P8Q67-M DO/USB3/TPM P8Q67-M DO/USB3/TPM Chassis intrusion connector Chapter 1: Product introduction 1-13

Section	Page
Notices	6
Safety information	7
About this guide	8
P8Q67-M DO Series specifications summary	9
Chapter 1	11
Product introduction	11
1.1 Before you proceed	11
1.2 Motherboard overview	12
1.2.1 Motherboard layout	12
1.2.2 Layout contents	13
1.3 Central Processing Unit (CPU)	13
1.4 System memory	14
1.4.1 Overview	14
1.4.2 Memory configurations	14
1.5 Expansion slots	18
1.5.1 Installing an expansion card	18
1.5.2 Configuring an expansion card	18
1.5.3 PCI slot	18
1.5.4 PCI Express x4 slot	18
1.5.5 PCI Express x16 slot	18
1.6 Jumpers	19
1.7 Connectors	20
1.7.1 Rear panel connectors	20
1.7.2 Internal connectors	22
1.8 Software support	29
1.8.1 Installing an operating system	29
1.8.2 Support DVD information	29
Chapter 2	30
BIOS information	30
2.1 Managing and updating your BIOS	30
2.1.1 ASUS Update utility	30
2.1.2 ASUS EZ Flash 2	31
2.1.3 ASUS CrashFree BIOS 3 utility	32
2.1.4 ASUS BIOS Updater	33
2.2 BIOS setup program	36
2.3 Main menu	39
2.3.1 System Language [English]	40
2.3.2 System Date [Day xx/xx/xxxx]	40
2.3.3 System Time [xx:xx:xx]	40
2.3.4 Security	40
2.4 Ai Tweaker menu	41
2.4.1 Memory Frequency [Auto]	42
2.4.2 iGPU Max. Frequency [Auto]	42
2.4.3 EPU Power Saving Mode [Disabled]	42
2.4.4 GPU Boost [OK]	42
2.4.5 DRAM Timing Control	42
2.4.6 CPU Power Management	42
2.4.7 Offset Mode Sign [+]	43
2.4.8 iGPU Offset Mode Sign [+]	44
2.4.9 DRAM Voltage [Auto]	44
2.4.10 VCCIO Voltage [Auto]	44
2.4.11 PCH Voltage [Auto]	44
2.4.12 Load-Line Calibration [Auto]	44
2.5 Advanced menu	45
2.5.1 Trusted Computing	45
2.5.2 CPU Configuration	45
2.5.3 System Agent Configuration	47
2.5.4 PCH Configuration	47
2.5.5 SATA Configuration	47
2.5.6 Intel TXT(LT) Configuration	48
2.5.7 USB Configuration	49
2.5.8 ME Subsystem	49
2.5.9 AMT Configuration	49
2.5.10 Onboard Devices Configuration	50
2.5.11 APM	51
2.5.12 Serial Port Console Redirection	52
2.6 Monitor menu	53
2.6.1 CPU Temperature / MB Temperature [xxxºC/xxxºF]	54
2.6.2 CPU / Chassis Fan Speed [xxxx RPM] or [Ignore] / [N/A]	54
2.6.3 CPU Q-Fan Control [Enabled]	54
2.6.4 Chassis Q-Fan Control [Enabled]	55
2.6.5 CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage	55
2.6.6 Anti Surge Support [Enabled]	55
2.7 Boot menu	56
2.7.1 Bootup NumLock State [On]	56
2.7.2 Full Screen Logo [Enabled]	56
2.7.3 Option ROM Messages [Force BIOS]	56
2.7.4 Setup Mode [EZ Mode]	57
2.7.5 Boot Option Priorities	57
2.7.6 Boot Override	57
2.8 Tools menu	58
2.8.1 ASUS EZ Flash Utility	58
2.8.2 ASUS SPD Information	58
2.8.3 ASUS O.C. Profile	58

Match case Limit results 1 per page

1-13

Chapter 1: Product introduction

Do not forget to connect the fan cables to the fan connectors. Insufﬁcient air ﬂow inside the

system may damage the motherboard components. These are not jumpers! Do not place

jumper caps on the fan connectors!

CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the

black wire of each cable matches the ground pin of the connector.

The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power.

CPU_FAN

CPU FAN PWM

CPU FAN IN

CPU FAN PWR

GND

P8Q67-M DO/USB3/TPM

P8Q67-M DO/USB3/TPM Fan connectors

GND

+12V

Rotation

CHA_FAN

Chassis intrusion connector (4-1 pin CHASSIS)

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The chassis

intrusion sensor or switch sends a high-level signal to this connector when a chassis

component is removed or replaced. The signal is then generated as a chassis intrusion

event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper

cap. Remove the jumper caps only when you intend to use the chassis intrusion

detection feature.

P8Q67-M DO/USB3/TPM

P8Q67-M DO/USB3/TPM Chassis intrusion connector

+5VSB_MB

Chassis Signal

GND

CHASSIS