Asus ROG Swift PG38UQ User Guide - Page 30

Power Setting, DisplayPort Stream, DSC Support, HDMI CEC, Information, All Reset

Get Asus ROG Swift PG38UQ PDF manuals and user guides View all Asus ROG Swift PG38UQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

• Power Setting：Select the power setting mode. If the setting is set to Standard Mode, it may result in higher power consumption. On the other hand, if the setting is set to Power Saving Mode, it may cause limited luminance performance. Power Setting Standard mode setting may result in higher power consumption. Power saving mode may cause limited luminance performance. Would you like to switch to Standard mode? YES NO • OSD Setup: Configure the OSD menu related settings. • OSD Position: Set the OSD menu position. • OSD Timeout: Adjust the OSD timeout. • Transparency: Adjust the OSD background from opaque to transparent. • Zoom By Remote Control: Select the OSD menu size when using the remote control. • Zoom by Hot Key: Select the OSD menu size when using the Control buttons. • DDC/CI: Enable/Disable the DDC/CI function. • DisplayPort Stream: Select DisplayPort 1.2 or DisplayPort 1.4 according to the graphic card DP version. • DSC Support: Enable/Disable the DSC (Display Stream Compression) function. • HDMI CEC: Allows power on/off control of the console device or setup box, such as Apple TV, Sony PlayStation, Xbox Series X/S, Nitendo Switch through the monitor. Default Off.Note: If the monitor is turned on, the CEC source device will automatically power on, and vice versa. If the CEC source device is turned on, the monitor will automatically power on.(*listed device is depend on test result). • If the monitor is turned on, the CEC source device will automatically power on, and vice versa. If the CEC source device is turned on, the monitor will automatically power on. • Information: Display the monitor information. • All Reset: Select YES to revert all settings to the factory default mode. 3-10 Chapter 3: General Instruction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
3-10
Chapter 3: General Instruction
•
Power Setting
：
Select the power setting mode.
If the setting is set to
Standard Mode
, it may result in higher
power consumption. On the other hand, if the setting is set
to
Power Saving Mode
, it may cause limited luminance
performance.
Power Setting
Standard mode setting may result in higher
power consumption. Power saving mode may
cause limited luminance performance.
Would you like to switch to Standard mode?
NO
YES
•
OSD Setup
: Configure the OSD menu related settings.
•
OSD Position: Set the OSD menu position.
•
OSD Timeout: Adjust the OSD timeout.
•
Transparency: Adjust the OSD background from opaque to
transparent.
•
Zoom By Remote Control: Select the OSD menu size when
using the remote control.
•
Zoom by Hot Key: Select the OSD menu size when using the
Control buttons.
•
DDC/CI: Enable/Disable the DDC/CI function.
•
DisplayPort Stream:
Select DisplayPort 1.2 or DisplayPort 1.4
according to the graphic card DP version.
•
DSC Support:
Enable/Disable the DSC (Display Stream
Compression) function.
•
HDMI CEC:
Allows power on/off control of the console device
or setup box, such as Apple TV, Sony PlayStation, Xbox Series
X/S, Nitendo Switch through the monitor. Default Off.Note: If the
monitor is turned on, the CEC source device will automatically
power on, and vice versa. If the CEC source device is turned on,
the monitor will automatically power on.(*listed device is depend
on test result).
•
If the monitor is turned on, the CEC source device will
automatically power on, and vice versa. If the CEC source
device is turned on, the monitor will automatically power on.
•
Information:
Display the monitor information.
•
All Reset:
Select YES to revert all settings to the factory default
mode.