Home » Asus Manuals » Servers » Asus TS500-E5 RX8 » Manual Viewer

Asus TS500-E5 RX8 User Guide - Page 67

USB connectors 10-1 pin USB34, USB56, CPU and system fan connectors 4-pin CPU_FAN1/2, REAR_FAN1/2,

Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

8. USB connectors (10-1 pin USB34, USB56) These connectors is for USB 2.0 ports. Connect the USB module cable to the connectors, then install the module to a slot opening at the back of the system chassis. The USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. DSAN-DX/TS500-E5 ® DSAN-DX/TS500-E5 USB 2.0 connectors USB56 USB34 NC GND USB_P6+ USB_P6USB+5V GND USB_P5+ USB_P5USB+5V NC GND USB_P4+ USB_P4USB+5V PIN 1 GND USB_P3+ USB_P3USB+5V PIN 1 The USB port module is purchased separately. 9. CPU and system fan connectors (4-pin CPU_FAN1/2, REAR_FAN1/2, FRNT_FAN1/2/3/4) The fan connectors support cooling fans of 350 mA-740 mA (8.88 W max.) or a total of 3.15 A-6.66 A (53.28 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors! CPU_FAN1 REAR_FAN2 CPU_FAN2 FRNT_FAN2 FRNT_FAN3 FRNT_FAN4 GND FAN Power FAN Speed PWM Control GND FAN Power FAN Speed PWM Control CPU_FAN1 CPU_FAN2 GND FAN Power FAN Speed PWM Control REAR_FAN1 REAR_FAN2 PWM Control FAN Speed FAN Power GND FRNT_FAN1 FRNT_FAN2 FRNT_FAN3 FRNT_FAN4 DSAN-DX/TS500-E5 ® GND FAN Power FAN Speed PWM Control GND FAN Power FAN Speed PWM Control GND FAN Power FAN Speed PWM Control PWM Control FAN Speed FAN Power GND DSAN-DX/TS500-E5 FAN connectors REAR_FAN1 FRNT_FAN1 ASUS TS500-E5 4-13

Section	Page
Contents	3
Notices	7
Safety information	8
About this guide	9
Chapter 1: Product introduction	11
1.1 System package contents	12
1.2 Serial number label	12
1.3 System specifications	13
1.4 Front panel features	15
1.4.1 Four Hot-Swap HDD Devices	15
1.4.2 Eight Hot-Swap HDD Devices	16
1.5 Rear panel features	17
1.5.1 Single power supply (PA4 model)	17
1.5.2 Redundant Power Supply (RX8 model)	17
1.6 Internal features	18
1.7 LED information	19
1.7.1 Front panel LEDs	19
1.7.2 Rear panel LEDs	20
Chapter 2: Hardware setup	21
2.1 Chassis cover	22
2.1.1 Removing the side cover	22
2.1.2 Reinstalling the side cover	23
2.2 Central Processing Unit (CPU)	24
2.2.1 Installing the CPU	24
2.2.2 Installing the CPU heatsink and fan	27
2.3 System memory	28
2.3.1 Overview	28
2.3.2 Memory configurations	28
2.3.3 Memory mirroring and sparing technology	30
2.3.4 Installing a DIMM	32
2.3.5 Removing a DIMM	32
2.4 Front panel assembly	33
2.4.1 Removing the front panel assembly	33
2.4.2 Reinstalling the front panel assembly	33
2.5 5.25-inch or 3.5-inch drives	34
2.5.1 Installing a 5.25-inch drive	34
2.5.2 Installing a 3.5-inch drive	35
2.6 SATA/SAS hard disk drives	36
2.6.1 Hot-swap HDD module	36
2.7 Expansion cards	40
2.7.1 Installing an expansion card	40
2.7.2 Installing ASUS PIKE RAID card	41
2.7.3 Configuring an expansion card	42
2.8 Cable connections	43
2.8.1 Motherboard connections	43
2.8.2 SATA/SAS backplane connections	44
2.9 Removable components	46
2.9.1 System fan	46
2.9.2 Chassis footpads	48
2.9.3 Power supply unit	49
Chapter 3: Installation options	51
3.1 Preparing the system for rack mounting	52
3.2 Attaching the inner rail to the server	52
3.3 Attaching the rails to the rack	53
3.4 Mounting the server to the rack	54
Chapter 4: Motherboard Info	55
4.1 Motherboard layout	56
4.2 Jumpers	58
4.3 Internal connectors	63
Chapter 5: BIOS setup	73
5.1 Managing and updating your BIOS	74
5.1.1 Creating a bootable floppy disk	74
5.1.2 AFUDOS utility	75
5.1.3 ASUS CrashFree BIOS 3 utility	78
5.2 BIOS setup program	79
5.2.1 BIOS menu screen	80
5.2.2 Menu bar	80
5.2.3 Navigation keys	80
5.2.4 Menu items	81
5.2.5 Sub-menu items	81
5.2.6 Configuration fields	81
5.2.7 Pop-up window	81
5.2.8 Scroll bar	81
5.2.9 General help	81
5.3 Main menu	82
5.3.1 System Time [xx:xx:xx]	82
5.3.2 System Date [Day xx/xx/xxxx]	82
5.3.3 Legacy Diskette A [Disabled]	82
5.3.4 SATA1–6; PATA Master/Slave	83
5.3.5 IDE Configuration	85
5.3.6 System Information	86
5.4 Advanced menu	87
5.4.1 USB Configuration	87
5.4.2 CPU Configuration	89
5.4.3 Chipset	91
5.4.4 Onboard Device Configuration	93
5.4.5 PCIPnP	94
5.5 Server menu	95
5.5.1 ASF Support [Enabled]	95
5.5.2 Remote Access Configuration	95
5.6 Power menu	97
5.6.1 ACPI 2.0 Support [Disabled]	97
5.6.2 ACPI APIC Support [Enabled]	97
5.7 Boot menu	100
5.7.1 Boot Device Priority	100
5.7.2 Boot Settings Configuration	101
5.7.3 Security	102
5.8 Exit menu	104
Chapter 6: RAID configuration	105
6.1 Setting up RAID	106
6.1.1 RAID definitions	106
6.1.2 Installing hard disk drives	107
6.1.3 Setting the RAID item in BIOS	107
6.1.4 RAID configuration utilities	107
6.2 LSI Software RAID Configuration Utility	108
6.2.1 Creating a RAID 0 or RAID 1 set	109
6.2.2 Creating a RAID 10 set	115
6.2.3 Adding or viewing a RAID configuration	119
6.2.4 Initializing the logical drives	122
6.2.5 Rebuilding failed drives	127
6.2.6 Checking the drives for data consistency	129
6.2.7 Deleting a RAID configuration	132
6.2.8 Selecting the boot drive from a RAID set	133
6.2.9 Enabling the WriteCache	134
6.3 Intel® Matrix Storage Manager Option ROM Utility	135
6.3.1 Creating a RAID 0 set (Stripe)	136
6.3.2 Creating a RAID 1 set (Mirror)	138
6.3.3 Creating a RAID 10 set (Stripe + Mirror)	139
6.3.4 Creating a RAID 5 set (Parity)	140
6.3.5 Deleting a RAID set	141
6.3.6 Resetting disks to Non-RAID	142
6.3.7 Exiting the Intel® Matrix Storage Manager	142
Chapter 7: Driver installation	143
7.1 RAID driver installation	144
7.1.1 Creating a RAID driver disk	144
7.1.2 Installing the RAID controller driver	147
7.2 Intel® chipset device installation	155
7.3 LAN driver installation	158
7.4 VGA driver installation	161
7.4.1 Windows® Server	161
7.5 Management applications and utilities installation	163
7.5.1 Running the support CD	163
7.5.2 Drivers menu	163
7.5.3 Management Software menu	164
7.5.4 Utilities menu	164

Match case Limit results 1 per page

ASUS TS500-E5

4-13

USB connectors (10-1 pin USB34, USB56)

These connectors is for USB 2.0 ports. Connect the USB module cable to

the connectors, then install the module to a slot opening at the back of the

system chassis. The USB connectors comply with USB 2.0 speciﬁcation that

supports up to 480 Mbps connection speed.

The USB port module is purchased separately.

DSAN-DX/TS500-E5

PIN 1

GND

USB_P6+

USB_P6-

USB+5V

GND

USB_P5+

USB_P5-

USB+5V

USB56

PIN 1

GND

USB_P4+

USB_P4-

USB+5V

GND

USB_P3+

USB_P3-

USB+5V

USB34

DSAN-DX/TS500-E5

USB 2.0 connectors

CPU and system fan connectors (4-pin CPU_FAN1/2, REAR_FAN1/2,

FRNT_FAN1/2/3/4)

The fan

connectors support cooling fans of 350 mA–740 mA (8.88 W max.)

or a total of 3.15 A–6.66 A (53.28 W max.) at +12V. Connect the fan cables

to the fan connectors on the motherboard, making sure that the black wire of

each cable matches the ground pin of the connector.

DO NOT forget to connect the fan cables to the fan connectors. Insufﬁcient air

ﬂow inside the system may damage the motherboard components. These are

not jumpers! DO NOT place jumper caps on the fan connectors!

DSAN-DX/TS500-E5

FRNT_FAN1

PWM Control

FAN Speed

FAN Power

GND

CPU_FAN1

GND

FAN Power

FAN Speed

PWM Control

CPU_FAN2

GND

FAN Power

FAN Speed

PWM Control

FRNT_FAN2

GND

FAN Power

FAN Speed

PWM Control

REAR_FAN1

GND

FAN Power

FAN Speed

PWM Control

FRNT_FAN3

GND

FAN Power

FAN Speed

PWM Control

REAR_FAN2

PWM Control

FAN Speed

FAN Power

GND

FRNT_FAN4

GND

FAN Power

FAN Speed

PWM Control

CPU_FAN1

REAR_FAN2

CPU_FAN2

FRNT_FAN2

FRNT_FAN3

FRNT_FAN4

FRNT_FAN1

REAR_FAN1

DSAN-DX/TS500-E5

FAN connectors